Sealey SMS2001M - User Manual

MANUAL DRILL BIT SHARPENER
MODEL NO: SMS2001M
1. SAFETY
 WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
9 Observe standard workshop safety procedures.
 WARNING! Take extreme caution when using this tool, the drill will require supporting, leaving the user with hands free to sharpen the
bit.
9 Wear approved eye protection and footwear. A range of personal safety equipment is available from your Sealey stockist.
8 DO NOT use this tool for any purpose other than that for which it has been designed.
8 DO NOT use to sharpen masonry drills.
8 DO NOT use adaptor sleeve if damaged.
9 Maintain tool in good and clean condition for best and safest
performance.
IMPORTANT: These instructions are provided as a guide only.
9 When not in use, clean and store complete.
2. INTRODUCTIONt
Fast, simple and effective way to sharpen drill bits. Suitable for use with
HSS, Titanium, Cobalt and Carbon Steel ranging from 3 to 10mm.
Fits with any drill with a 43mm collar (not to be used hammer function).
3. SPECIFICATION
Model no: .............................................................SMS2001M
Drill bit range: .........................................................................
3, 3.5, 4, 4.2, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10mm
Collar size: ...................................................................43mm
4. OPERATION
4.1. Setting
4.1.1. Support the drill with axis vertical.
4.1.2. Close the jaws of the drill chuck fully to obtain maximum
projection.
4.1.3.  Trialtthesharpenerthreeprongedinternalcoupling,seeg.2,
 ontothechuckjawsasshowning.1
4.1.4. Adjust the length of the jaws to suit internal coupling.
4.1.5. Fit the adaptor tube to both the drill shoulder and the sharpener
 asshowning.1withequalgriplength.
4.1.6. Apply pressure to the sharpener, forcing the drill jaws to engage
 rmlywiththeinternalcoupling.Clampthetubewiththetwocap
screws (5mm hex).
4.1.7.  Turnthe“STONE”(g.3)knobtothedownposition.
4.2. Drill sharpening
4.2.1. Set the drill speed to fastest setting speed and turn on.
4.2.2. Offer the drill bit to be sharpened into the correct aperture.
4.2.3.  Rotatethedrillbitslightlywhilstloweringontotheutelocation
ledges. Resistance will be felt when reached.
4.2.4.  Turnthe“STONE”(g.3)knobtowardtheuppositionwhilst
rotating the drill slightly until the grinding wheel engages with the
bit.
4.2.5. Observe the bit for ground tip.
4.2.6. Alternate drill bit 180° cutting face to cutting face for even
sharpening as adjustments to “STONE” knob are made. Small
adjustments recommended when grinding. Turn off the drill
between observations.
SMS2001M | Issue 2 (H,2,3,4,5,6,F) 22/02/18
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
2
Ø43
Drill
1
g.1
Rotation
direction
Rotation
direction
g.2
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
g.3

Summary

Manual Drill Bit Sharpener Safety and Setup

General Safety Precautions

Ensure adherence to health, safety, and workshop regulations when using the tool.

Personal Protective Equipment (PPE)

Mandatory use of approved eye protection and footwear during operation.

Product Overview and Specifications

Introduction to Drill Bit Sharpener

Fast, simple, effective tool for sharpening HSS, Titanium, Cobalt, Carbon Steel bits (3-10mm).

Technical Specifications

Model SMS2001M, drill bit range 3-10mm, collar size 43mm.

Drill Bit Sharpening Operation

Setting Up the Drill Sharpener

Steps for securing the drill, chuck jaws, and attaching the sharpener adaptor.

Sharpening Procedure

Detailed steps for setting drill speed, offering bit, rotating, and adjusting stone for effective sharpening.

Troubleshooting and Cleaning Guide

Troubleshooting Common Issues

Addresses problems like bit overheating, excessive material removal, and grinder malfunction.

Cleaning and Maintenance

Instructions for cleaning internal and external parts using air lines and damp cloths.

Product Information and Support

Environmental Protection and Disposal

Guidance on recycling materials and proper product disposal according to local regulations.

Warranty and Liability

Outlines the 12-month warranty, required proof of purchase, and disclaimer for misuse.

Sealey SMS2001M Specifications

General

Model	SMS2001M
Supply	230V
Disc Diameter	200mm
Maximum Grinding Wheel Thickness	25mm
Type	Bench Grinder
Power Source	Electric
Voltage	230V