Sealey STW308 - User Manual

INSTRUCTIONS FOR:
3/8” square drive digital torque
wrench 8-85nm
MODEL NO: stw308
1. safety
2. introduction
3. specification
 warning! do not use the torque wrench if damaged or thought to be faulty.
 Ensure all workshop safety rules, regulations and conditions are complied with when using the torque wrench.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the working area.
 Avoid over-torquing the wrench (110% of maximum torque range) as this will cause loss of accuracy.
 Keep the wrench away from magnets.
 In operation when you hear the continuous tone, stop pulling immediately especially in case the target torque/ angle is low.
 Ensure all sockets, extensions and drivers are rated correctly and are of flawless construction. Avoid using adaptors and extensions for
best accuracy.
 do not use the torque wrench if the batteries are low, torque accuracy will be affected.
 do not use the wrench as a hammer or similar.
 do not use on live electrical circuits the plastic handle is not insulated.
 do not subject the wrench to excessive force or shocks.
 do not drop, throw, or violently shake the wrench.
 do not operate the wrench in damp conditions.
 do not operate the wrench in dusty conditions.
 do not push on the LCD panel.
 do not use wrench until first instructed in its use by a qualified person.
 do not leave the wrench in a place exposed to excessive heat, humidity or direct sunlight.
 do not use organic solvents such as alcohol or thinners to clean the wrench.
 After use, turn the wrench off, clean with a soft dry cloth, place torque wrench in its storage case, and store in a safe, dry, childproof
location.
 Remove the batteries if the torque wrench is not to be used for a long time, to prevent damage from leaking.
Rugged and resilient digital torque wrench suitable for workshop and factory use. LCD read-out with LED, audible alarm and vibration indicating
achieved and target torque levels. Preset track, peak or desired torque levels using simple push button menu. Selectable read-out in Nm, lb.in,
lb.ft, or kgf.m. Reversible Chrome Vanadium 72-tooth ratchet allows torque reading in either direction. Accurate to ±2% between 10% and 100%
of wrench’s stated capacity. Supplied with test certicate and storage case.
3.1. Specication
Model No: ...................... stw308
Drive: .......................... 3/8”Sq
Length: . . . . . . . . . . . . . . . . . . . . . . . . . 335mm
Range: ......................... 8-85Nm
Operating Voltage: ................ 3V
Cell Qty x Type: .................. 2 x AAA (supplied)
Torque Accuracy: ................. ±2%(C.W. / C.C.W. of reading,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10% to 100% of full scale)
Torque Resolution: . . . . . . . . . . . . . . . . 0.1N.m / 1lbf-in / 0.1lbf-ft / 0.1Kgf.m
Gear Teeth:...................... 72
Units: .......................... N.m / lbf-in / lbf-ft / Kgf.m
Operating Temperature: ............ 0 ~ 40°C / 32~104°F
Storage Temperature:.............. -20 ~ 45°C / -4 ~113°F
Humidity:........................ Humidity up to 60% Non-condensing
3.2. Calibration check
We recommend to ensure continued accuracy the
calibration of each wrench should be checked annually,
beginning one year after rst use. Calibration should
also be checked after any impact, over-torquing or other
misuse. Contact your Sealey Dealer to arrange
recalibration.
STW308 Issue: 1 - 14/05/14
Original Language Version
© Jack Sealey Limited
IMPORTANT: please read these instructions carefully. note the safe operational requireMents, warnings & cautions. use the
product correctly and with care for the purpose for which it is intended. failure to do so May cause daMage and/or
personal inJury and will invalidate the warranty. Keep these instructions safe for future use.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.

Summary

Safety Guidelines

General Safety Precautions

Ensure correct balance, footing, and tool integrity for safe operation.

Usage Prohibitions

Lists actions and conditions to strictly avoid to prevent damage or injury.

Important Safety Notice

Emphasizes careful reading of instructions for safe and correct product use.

Product Introduction

Product Overview

Description of the rugged and resilient digital torque wrench for workshop use.

Specifications

Details model, drive, length, range, accuracy, and units of the torque wrench.

Calibration Check

Recommends annual calibration checks and checks after impact or misuse.

Operation and Controls

Display Overview

Explanation of the digital display elements including torque value, units, and indicators.

Control Panel Functions

Details the buttons for power, memory, zeroing, and illumination.

Preparation for Use

Instructions for battery installation and preparation before operating the wrench.

Turning Tool On;Off

Procedure for powering the torque wrench on and off using the designated button.

Advanced Operation

Peak and Track Mode

Setting and understanding the Peak and Track modes for torque measurement.

Unit Selection

Guide to selecting desired torque units (Nm, lbf.ft, lbf.in, kgf.m).

Auto Power Off Setting

Configuration for automatic power-off duration to conserve battery.

Target Torque Programming

Instructions for setting and saving up to five preset target torque values.

Operating the Wrench

Step-by-step guide on how to use the torque wrench to achieve target torque.

Environmental and Support Information

Environmental Protection

Guidance on recycling tools, accessories, and packaging responsibly.

WEEE Regulations

Instructions for proper disposal of the product according to WEEE directives.

Battery Removal and Disposal

Information on battery removal and disposal according to local authority guidelines.

Parts Support and Contact

Information on obtaining parts, warranty, and contacting Sealey for support.

Sealey STW308 Specifications

General

Model	STW308
Type	Air Impact Wrench
Drive Size	1/2" Square Drive
Blows Per Minute	1200bpm
Air Inlet	1/4" BSP
Operating Air Pressure	90psi
Nett Weight	2.6kg