Sealey SMS2008 - User Manual

1. SAFETY INSTRUCTIONS
1.1 ELECTRICAL SAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1 and 1.1.2
and use a Portable Appliance Tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Inspect regularly power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6 Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7 DO NOT pull or carry the appliance by the power cable.
1.1.8 DO NOT pull the plug from the socket by the cable.
1.1.9 DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends
beyond the cable restraint and that the restraint is tight. Double insulated products, which are always marked with this symbol , are
fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as indicated above - DO NOT connect either wire to
the earth terminal.
1.1.10 Products which require more than 13A are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2 GENERAL SAFETY
 Disconnect the sharpener from the mains power before changing accessories, servicing or performing any maintenance.
 Maintain sharpener and stone in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
 Replace or repair damaged parts. Use genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.
 The grinding wheel or stone must only be changed by persons holding an appropriate grinding wheel certificate.
 Wear approved safety goggles, ear defenders and safety gloves.
 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
 Use sharpener in a suitable work area, keep area clean, tidy and free from unrelated materials, and ensure adequate lighting.
 Maintain correct balance and footing. DO NOT over-reach and ensure the floor is not slippery. Wear non slip shoes.
 Keep non essential persons away from the working area.
 DO NOT operate the sharpener if any parts are missing or the sharpener is damaged.
 DO NOT use the sharpener for a task it was not designed to perform.
 DO NOT operate sharpener where there are flammable liquids or gasses.
 DO NOT get the sharpener wet or use in damp or wet locations.
 DO NOT switch the sharpener on whilst the stone is in contact with the workpiece.
 DO NOT touch the workpiece immediately after sharpening as it will be very hot.
 DO NOT try to cool the sharpening wheel with water or other lubricants.
 DO NOT touch the sharpening disc whilst operating, or whilst plugged into the mains power.
 DO NOT leave the sharpener running unattended.
 DO NOT operate the sharpener when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT attach modules if the wheel is still moving and DO NOT use without a module in place.
 The motor is specially rated for intermittant use, use a maximum of 15 minutes continuous use.
 When not in use switch sharpener off, remove plug from power supply.
Original Language Version
SMS2008
Issue:2(I) - 21/10/14
© Jack Sealey Ltd
INSTRUCTIONS FOR:
DRILL BIT SHARPENER - BENCH MOUNTING 80W
MODEL No: SMS2008
RECOMMENDED FUSE RATING 5 AMP
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.

Summary

Safety Instructions

Electrical Safety Precautions

Ensuring compliance with electrical safety standards, including RCCB/RCD use and owner responsibilities.

Power Cable and Plug Safety

Guidelines for inspecting, handling, and maintaining power cables, plugs, and connectors to prevent hazards.

Fuse and Voltage Matching

Ensuring the appliance voltage matches the power supply and the plug is fitted with the correct fuse.

Plug Wiring and Double Insulation

Instructions for wiring BS 1363/A plugs and handling double insulated products.

High Current Appliances and Extension Reels

Advice on connecting high current appliances and using suitable extension reels with RCD protection.

General Operational Safety

Includes disconnecting power, maintaining condition, using PPE, and keeping the work area safe.

Prohibited Operations and Warnings

Lists operations and conditions to avoid, such as using damaged parts or operating near flammables.

Usage and Storage Guidelines

Recommendations on motor duty cycle, switching off when not in use, and proper storage.

Introduction and Specifications

Operation and Sharpening

Setting the Drill Bit Holder

Steps for removing, inserting, and tightening the drill bit within its holder.

Drill Bit Alignment

Ensuring the drill bit flutes are horizontally aligned in the holder for correct sharpening.

Securing the Drill Bit Holder

Final tightening of the locking ring before moving the holder to the sharpening location.

Transferring to Sharpening Location

Moving the secured drill bit holder to the sharpening station for the sharpening process.

Initiating Sharpening

Switching on the machine and engaging the drill bit holder into the sharpening location.

Performing Sharpening Passes

Technique for sharpening by rocking the holder, including repeating and rotating the bit.

Grinding Process

Engaging the drill bit holder in the grinding location and working it back and forth.

Maintenance and Environmental

Cleaning and Maintenance

Instructions for cleaning the sharpener, removing metal filings, and general upkeep.

Fuse Replacement

Locating and replacing the internal fuse, emphasizing using the correct rating.

Environmental Protection

Guidelines for recycling unwanted materials and disposing of tools responsibly.

WEEE Regulations Compliance

Information on disposing of the product at its end-of-life according to EU directives.

Sealey SMS2008 Specifications

General

Brand	Sealey
Model	SMS2008
Category	Power Tool
Language	English