Seca 6641321108 - User Manual

Questions and Answers

C
Calvin MerrittAug 20, 2025
Why does the display show 'bAtt' on my Seca 6641321108 Scales?
- V
  Vincent CampbellAug 20, 2025
  If the display shows "bAtt" on your Seca Scales, it indicates that the battery block is discharged. You should charge the battery block.
D
Diana WilliamsAug 22, 2025
What does 'Er:X:12' mean on Seca 6641321108?
- L
  Leroy WoodAug 22, 2025
  If the display shows "Er:X:12" on your Seca Scales, it means the scale has been switched on with too high a load. Remove the load from the scale and restart the scale.
W
William CampbellAug 25, 2025
What does 'Er:X:11' mean on Seca 6641321108 Scales display?
- B
  Briana KellyAug 25, 2025
  If the display shows "Er:X:11" on your Seca Scales, it indicates that the scale has too high a load or too high a load in one corner. Remove the load from the scale or distribute the weight more evenly. Restart the scale.
K
Kathy WongAug 26, 2025
What does error 'Er:X:16' mean on Seca Scales?
- J
  James GarciaAug 27, 2025
  If the display shows "Er:X:16" on your Seca Scales, it means the scale was caused to oscillate, and the zero point could not be determined. Restart the scale.
H
herreraaimeeAug 28, 2025
What to do if the display shows 'StOP' on Seca 6641321108 Scales?
- D
  Deborah MooreAug 28, 2025
  If the display shows "StOP" on your Seca Scales, it means the maximum load has been exceeded. Remove some of the load from the scale.
M
mariastevensAug 30, 2025
How to fix no weight displayed on Seca Scales?
- M
  Melissa FrankAug 30, 2025
  If no weight is displayed when there is a load on your Seca Scales, the scale may not have power. Check whether the scale is switched on.
N
Natalie Long DDSSep 1, 2025
What to do if Seca 6641321108 Scales doesn't show 0.0 before weighing?
- J
  Jodi McbrideSep 1, 2025
  If "0.0" doesn't appear before weighing on your Seca Scales, it might be because a load was already on the scale when it was switched on. Remove the load from the scale, then switch the scale off and back on again.
J
John FletcherSep 3, 2025
Why does the display show 'tEMP' on my Seca 6641321108 Scales?
- R
  Robin RogersSep 3, 2025
  If the display shows "tEMP" on your Seca Scales, it means the ambient temperature of the scale is either too high or too low. Set up the scale in an ambient temperature between +10 °C and +40 °C. Wait approximately 15 minutes for the device to adapt to the ambient temperature.
D
Debbie JamesSep 5, 2025
Why does 'Er:X:72' appear when I press Enter on Seca 6641321108?
- U
  ufoxSep 5, 2025
  If you press the Enter key (send/print) and the display shows "Er:X:72" on your Seca Scales, it indicates that data transmission is not possible because no wireless group is set up. Set up wireless group (see "Setting up a wireless group (Lrn)" on page 87).
K
Kimberly KennedySep 7, 2025
What does 'Er:X:71' mean when pressing Enter on Seca 6641321108 Scales?
- J
  Joseph ObrienSep 7, 2025
  If you press the Enter key (send/print) and the display shows "Er:X:71" on your Seca Scales, it indicates that data transmission is not possible because the wireless module is deactivated. Activate wireless module (see "Activating the wireless module (SYS)" on page 87).