Seca 684 - User Manual

Other manuals for Seca 684

Instruction Manual113 pages

Instruction Manual And Guarantee39 pages

Questions and Answers

S
Stephanie RobinsonAug 20, 2025
What to do if the display "StOP" appears on Seca 684?
- E
  erochaAug 20, 2025
  The "StOP" message indicates that the maximum load has been exceeded. Remove some of the load from the scale.
I
Isaiah RubioAug 22, 2025
Why is no weight displayed when there is a load on my Seca 684 Scales?
- K
  Kaylee MillsAug 22, 2025
  This issue may occur if the scale is not switched on. Check that the scale is powered on.
J
jennifergarrettAug 25, 2025
What to do if the display "tEMP" appears on Seca Scales?
- M
  Micheal HopkinsAug 25, 2025
  The "tEMP" message indicates that the ambient temperature is too high or too low for the scale to function correctly. Set up the scale in a room where the ambient temperature is between +10 °C and +40 °C. Then, wait approximately 15 minutes to allow the device to adjust to the ambient temperature.
R
robert66Aug 27, 2025
What does "Er:X:11" mean on Seca 684 and how to fix it?
- S
  Shelly PalmerAug 27, 2025
  The error message "Er:X:11" indicates that the scale has too high a load or too much load in one corner. Remove some of the load or distribute the weight more evenly. Then, restart the scale.
S
Stephen JacobsAug 28, 2025
What does "Er:X:12" mean on Seca Scales and how to resolve it?
- T
  theresabrownAug 28, 2025
  The error message "Er:X:12" indicates that the scale was switched on with too high a load. Remove the load from the scale, and then restart the scale.
L
Lauren CraigAug 30, 2025
How to fix Seca 684 Scales when 0.00 does not appear before weighing?
- J
  James RobinsonAug 30, 2025
  If '0.00' does not appear before weighing, it might be because a load was already on the scale when it was switched on. Remove the load, then switch the scale off and back on again.
M
Mrs. Leslie RuizSep 1, 2025
What does "Er:X:16" mean on Seca Scales and how to troubleshoot it?
- L
  Laura JonesSep 1, 2025
  The error message "Er:X:16" means that the scale was caused to oscillate, and the zero point could not be determined. Restart the scale.
W
Wayne MillerSep 3, 2025
Why do Seca 684 transmit measurement results and beep twice after the first switch on?
- A
  Allison BurtonSep 3, 2025
  This happens when the scale can't send measurement results to the wireless receiver (like a Seca wireless printer or a PC with a Seca USB wireless adapter). Ensure the scale is integrated into the wireless network and that the receiver is switched on. Interference from HF equipment (like cell phones) nearby can also cause this. Keep such equipment at least 1 meter away from the scale and receiver.
J
Jacqueline PenaSep 5, 2025
What does "Er:X:71" mean on Seca 684 Scales and how to resolve it?
- B
  Becky HernandezSep 5, 2025
  The error message "Er:X:71" indicates that data transmission is not possible because the wireless module is deactivated. Activate the wireless module.
K
Kathryn WilsonSep 7, 2025
What does "Er:X:72" mean on Seca 684 and how to resolve it?
- B
  Brian MillerSep 7, 2025
  The error message "Er:X:72" indicates that data transmission is not possible because no wireless group is set up. Set up a wireless group.