Security Link SL150 - Page 114

Security Link SL150

144 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

SL150 Installation and Setup Guide

22–4

Table of Contents

Default Chapter3
- Recommendations for Proper Protection3
- Table of Contents4
List of Figures7
Conventions Used in this Manual8
SECTION 1 Introduction9
- General Description9
- Features9
SECTION 2 Installing the Control13
- Mounting the Cabinet13
- Installing the Lock (if Used)13
- Figure 1. Installing the Cabinet Lock13
- Mounting the Control's Circuit Board Alone in the Cabinet14
- Mounting Control and RF Receiver Circuit Boards Together in the Cabinet14
- Figure 2. Mounting the PC Board14
- Figure 3. Mounting the PC Board and RF Receiver Together in the Cabinet15
- Standard Phone Line Connections16
- Figure 4. Telephone Line Connections16
- Wiring the AC Transformer17
- Figure 5. Connections of 4300 Transformer to the Control Board17
- Installing the Backup Battery18
- Earth Ground Connections18
SECTION 3 Installing Remote Keypads19
- Keypads that May be Used19
- Wiring to the Keypads19
- Mounting the Keypads20
- Supplementary Power for Additional Keypads20
- Figure 6. Keypad Connections to the Control Board20
- Preliminary Checkout Procedure21
- Figure 7. Using a Supplementary Power Supply for Keypads21
SECTION 4 Basic Hardwired Zones 1-823
- Installing the Hardwired Zones23
- Figure 24. SL150 Summary of Connections23
- Figure 8. 2-Wire Smoke Detector Connected to Zone 124
- Figure 9. 4-Wire Smoke Detector Connections (Zones 2-7)25
- Figure 10. Glassbreak Detector Connections to Zone 826
- Remote Keyswitch (Zone 7)27
- Figure 11. Keyswitch Wiring Without the 4300 Transformer28
- Programming Basic Hardwired Zones30
- Checkout Procedure for Hardwired Zones30
SECTION 5 Wired Zone Expansion33
- Installing Zone Expansion Units33
- Connections and Setup33
- Figure 13. Wiring Connections - 4219 Expansion Module34
- Figure 14. Wiring Connections - 4229 Expansion/Relay Module34
- Programming Wired Expansion Zones35
- Checkout Procedure for Wired Expansion Zones35
SECTION 6 Wireless Expansion (5800 System)37
- About Wireless Expansion37
- Installing the 5881/5882 Receiver38
- Figure 15. 5881/5882 RF Receiver (Cover Removed)38
- Installing the 5800TM Module39
- Jam Detection and Reporting39
- About 5800 Series Transmitters39
- Series Transmitters Table42
- Installing 5800 Series Transmitters43
SECTION 7 Relay Outputs & Powerline Carrier Devices45
- About Relays and Powerline Carrier Devices45
- 4204 And 4229 Relay Modules45
- Figure 16. 4229 Connections to Control Panel46
- Powerline Carrier Devices47
- Figure 17. 4204 Connections to Control Panel47
- Programming Relay Outputs48
- Figure 18. 4300 Transformer Wiring Connections48
SECTION 8 4285 & 4286 VIP Module49
- About the 4285 & 4286 VIP Module49
- Installing the Phone Module49
- Figure 19. 4285/4286 VIP Module Wiring Connections51
- Programming the 4285/4286 VIP Module52
- Checking 4285/4286 VIP Module Operation52
SECTION 9 External Sounders53
- Compatible Sounders53
- NFPA Requirements53
- Sounder Connections and Power54
- Sounder Supervision54
- Testing the Sounder54
- Figure 20. Sounder Wiring54
SECTION 10 Long Range Radio55
- About Long Range Radio55
- Wiring Connections55
- Figure 21. Long Range Radio Connections55
- Dynamic Signaling Feature56
SECTION 11 Audio Alarm Verification (AAV) Unit57
- About Audio Alarm Verification57
- Wiring Connections57
- Figure 22. Connection of AAV Unit When Not Using a 4285/4286 VIP Module58
- Figure 23. Connection of AAV Unit When also Using a 4285 or 4286 VIP Module58
SECTION 12 Final Power-Up59
- Earth Ground Connections59
- AC Power-Up59
- Connecting the Backup Battery59
- Battery Tests60
SECTION 13 Mechanics of Programming61
- About Programming61
- Entering Program Mode62
- Programming a Data Field62
- Reviewing a Data Field/Erasing an Entry62
- Interactive Mode Programming ( 56, 58, 80, 81, 82)62
- Loading Factory Defaults63
- Programming System Setup Fields63
- Exiting the Programming Mode63
SECTION 14 Zone Response Type Definitions65
- Zone Type Definitions65
SECTION 15 Data Field Descriptions69
- Descriptions of System Data Fields69
SECTION 16 Zone Programming83
- About Zone Programming83
  - 56 Zone Programming Procedures83
  - 58 Expert Programming Mode Procedures86
- To Remove a Zone88
- To Delete a Transmitter Serial Number89
- To Enter and Duplicate Wireless Keys89
SECTION 17 Output Device Programming93
- Programming Options Defined93
- Programming Output Relays and Powerline Carrier Devices95
SECTION 18 Zone Lists99
- About Zone List Menu Mode99
- Zone List Displays99
- Pager 1 Reporting - Zone List 06100
- Pager 2 Reporting - Zone List 07100
SECTION 19 Alpha Descriptor Programming101
- About Alpha Descriptor Programming101
- Zone Descriptors101
- Programming Zone Descriptors (Program Menu Mode 82)101
- Adding Custom Words103
SECTION 20 Macros (Speedkey)107
- About Macros107
- Macro Key (Speedkey) Programming107
SECTION 21 Remote Programming and Control (Downloading)109
- About Remote Programming109
- Equipment Required109
- Initial Download110
- Remote Programming Commands110
- Remote Programming Advisory Notes110
SECTION 22 System Communication111
- Panel Communication with Central Station111
- Report Code Formats111
SECTION 23 System Operation115
- Security Codes115
- Keypad Functions116
SECTION 24 Testing the System121
- Test Procedure121
SECTION 25 Troubleshooting Guide123
- Contacting Technical Support125
SECTION 26 Specifications & Accessories127
- Specifications127
- Accessories (Compatible Devices)129
APPENDIX A 5800 RF System Wireless Transmitters131
APPENDIX A 5800 RF System Wireless Transmitters131
- 5800 Series Transmitter Input Loop Identification131
APPENDIX B Regulatory Agency Statements133
APPENDIX C Warnings and Limitations135
Index137
- Limited Warranty144