Security Link SL150 - Page 2

Security Link SL150

144 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

ii

.

Table of Contents

Default Chapter3
- Recommendations for Proper Protection3
- Table of Contents4
List of Figures7
Conventions Used in this Manual8
SECTION 1 Introduction9
- General Description9
- Features9
SECTION 2 Installing the Control13
- Mounting the Cabinet13
- Installing the Lock (if Used)13
- Figure 1. Installing the Cabinet Lock13
- Mounting the Control's Circuit Board Alone in the Cabinet14
- Mounting Control and RF Receiver Circuit Boards Together in the Cabinet14
- Figure 2. Mounting the PC Board14
- Figure 3. Mounting the PC Board and RF Receiver Together in the Cabinet15
- Standard Phone Line Connections16
- Figure 4. Telephone Line Connections16
- Wiring the AC Transformer17
- Figure 5. Connections of 4300 Transformer to the Control Board17
- Installing the Backup Battery18
- Earth Ground Connections18
SECTION 3 Installing Remote Keypads19
- Keypads that May be Used19
- Wiring to the Keypads19
- Mounting the Keypads20
- Supplementary Power for Additional Keypads20
- Figure 6. Keypad Connections to the Control Board20
- Preliminary Checkout Procedure21
- Figure 7. Using a Supplementary Power Supply for Keypads21
SECTION 4 Basic Hardwired Zones 1-823
- Installing the Hardwired Zones23
- Figure 24. SL150 Summary of Connections23
- Figure 8. 2-Wire Smoke Detector Connected to Zone 124
- Figure 9. 4-Wire Smoke Detector Connections (Zones 2-7)25
- Figure 10. Glassbreak Detector Connections to Zone 826
- Remote Keyswitch (Zone 7)27
- Figure 11. Keyswitch Wiring Without the 4300 Transformer28
- Programming Basic Hardwired Zones30
- Checkout Procedure for Hardwired Zones30
SECTION 5 Wired Zone Expansion33
- Installing Zone Expansion Units33
- Connections and Setup33
- Figure 13. Wiring Connections - 4219 Expansion Module34
- Figure 14. Wiring Connections - 4229 Expansion/Relay Module34
- Programming Wired Expansion Zones35
- Checkout Procedure for Wired Expansion Zones35
SECTION 6 Wireless Expansion (5800 System)37
- About Wireless Expansion37
- Installing the 5881/5882 Receiver38
- Figure 15. 5881/5882 RF Receiver (Cover Removed)38
- Installing the 5800TM Module39
- Jam Detection and Reporting39
- About 5800 Series Transmitters39
- Series Transmitters Table42
- Installing 5800 Series Transmitters43
SECTION 7 Relay Outputs & Powerline Carrier Devices45
- About Relays and Powerline Carrier Devices45
- 4204 And 4229 Relay Modules45
- Figure 16. 4229 Connections to Control Panel46
- Powerline Carrier Devices47
- Figure 17. 4204 Connections to Control Panel47
- Programming Relay Outputs48
- Figure 18. 4300 Transformer Wiring Connections48
SECTION 8 4285 & 4286 VIP Module49
- About the 4285 & 4286 VIP Module49
- Installing the Phone Module49
- Figure 19. 4285/4286 VIP Module Wiring Connections51
- Programming the 4285/4286 VIP Module52
- Checking 4285/4286 VIP Module Operation52
SECTION 9 External Sounders53
- Compatible Sounders53
- NFPA Requirements53
- Sounder Connections and Power54
- Sounder Supervision54
- Testing the Sounder54
- Figure 20. Sounder Wiring54
SECTION 10 Long Range Radio55
- About Long Range Radio55
- Wiring Connections55
- Figure 21. Long Range Radio Connections55
- Dynamic Signaling Feature56
SECTION 11 Audio Alarm Verification (AAV) Unit57
- About Audio Alarm Verification57
- Wiring Connections57
- Figure 22. Connection of AAV Unit When Not Using a 4285/4286 VIP Module58
- Figure 23. Connection of AAV Unit When also Using a 4285 or 4286 VIP Module58
SECTION 12 Final Power-Up59
- Earth Ground Connections59
- AC Power-Up59
- Connecting the Backup Battery59
- Battery Tests60
SECTION 13 Mechanics of Programming61
- About Programming61
- Entering Program Mode62
- Programming a Data Field62
- Reviewing a Data Field/Erasing an Entry62
- Interactive Mode Programming ( 56, 58, 80, 81, 82)62
- Loading Factory Defaults63
- Programming System Setup Fields63
- Exiting the Programming Mode63
SECTION 14 Zone Response Type Definitions65
- Zone Type Definitions65
SECTION 15 Data Field Descriptions69
- Descriptions of System Data Fields69
SECTION 16 Zone Programming83
- About Zone Programming83
  - 56 Zone Programming Procedures83
  - 58 Expert Programming Mode Procedures86
- To Remove a Zone88
- To Delete a Transmitter Serial Number89
- To Enter and Duplicate Wireless Keys89
SECTION 17 Output Device Programming93
- Programming Options Defined93
- Programming Output Relays and Powerline Carrier Devices95
SECTION 18 Zone Lists99
- About Zone List Menu Mode99
- Zone List Displays99
- Pager 1 Reporting - Zone List 06100
- Pager 2 Reporting - Zone List 07100
SECTION 19 Alpha Descriptor Programming101
- About Alpha Descriptor Programming101
- Zone Descriptors101
- Programming Zone Descriptors (Program Menu Mode 82)101
- Adding Custom Words103
SECTION 20 Macros (Speedkey)107
- About Macros107
- Macro Key (Speedkey) Programming107
SECTION 21 Remote Programming and Control (Downloading)109
- About Remote Programming109
- Equipment Required109
- Initial Download110
- Remote Programming Commands110
- Remote Programming Advisory Notes110
SECTION 22 System Communication111
- Panel Communication with Central Station111
- Report Code Formats111
SECTION 23 System Operation115
- Security Codes115
- Keypad Functions116
SECTION 24 Testing the System121
- Test Procedure121
SECTION 25 Troubleshooting Guide123
- Contacting Technical Support125
SECTION 26 Specifications & Accessories127
- Specifications127
- Accessories (Compatible Devices)129
APPENDIX A 5800 RF System Wireless Transmitters131
APPENDIX A 5800 RF System Wireless Transmitters131
- 5800 Series Transmitter Input Loop Identification131
APPENDIX B Regulatory Agency Statements133
APPENDIX C Warnings and Limitations135
Index137
- Limited Warranty144