What does LEAK mean on my SEFAM DreamStar Humidifier?
If 'LEAK : ++ (or +++ or ++++)' is displayed on the screen of your SEFAM Humidifier, it means the device has detected a high level of leak. Adjust your mask, mask cushion, and/or harness until you achieve a good mask fit.
How to stop dry eyes caused by SEFAM DreamStar Humidifier?
If you're experiencing dry or irritated eyes while using the SEFAM Humidifier, it's likely due to air leakage around the mask. Try repositioning the mask to ensure a better seal.
How to fix high pressure discomfort from SEFAM DreamStar?
If you're feeling discomfort because the pressure is too high with your SEFAM Humidifier, use the pressure ramp feature when you go to sleep. Relax and breathe slowly through your nose. If the pressure delivered by the device seems to have changed, contact the home care provider to have the device pressure checked, as the pressure levels have been prescribed by your physician and can be changed only by medical prescription.
Why is my SEFAM Humidifier not heating the water?
If the SEFAM Humidifier doesn't seem to be heating water, check that the heat level is set between 1 and 10. Also, confirm that the heated humidifier indicator is displayed on the screen and is not blinking. If the indicator is blinking or not present, contact your home care provider. Note that the heated humidification feature cannot be used when the device is battery-powered.
What to do if my skin is red from using SEFAM DreamStar Humidifier mask?
If you experience skin redness from your SEFAM Humidifier mask, the headgear may be too tight or the mask size may be too small; try adjusting the headgear. If redness persists, you might be having an allergic reaction to the mask components. In that case, stop using the mask and contact your doctor or home care provider.
Why is the air from my SEFAM DreamStar too hot?
If the air from your SEFAM Humidifier is too hot, the air intake filters may be dirty, so clean or replace them as needed. Also, check if the air intake is blocked by bedclothes or clothing and move them away. Finally, the room temperature might be too high, so lower the room temperature and ensure the device is away from heat sources. Remove the patient circuit from under any covers.
Why SEFAM DreamStar Humidifier doesn't turn on?
If your SEFAM Humidifier device isn't lighting up, start by checking that the power supply cord is correctly plugged into the power port, and ensure the cord is properly connected to both the device and the power source. Then, plug another device into the power source to confirm that the outlet is working. If these steps don't solve the issue, contact your home care provider.
What to do if there's too much water in my SEFAM DreamStar mask?
If you notice excessive water droplets in the mask or patient circuit of your SEFAM Humidifier, it could be due to several reasons. First, check if the water level in the water chamber exceeds the maximum fill line and pour out any excess. A small amount of water droplets can be normal, especially in winter. You can also adjust the heat level of your device. Additionally, try routing the patient circuit under your blanket to reduce condensation.
General| Brand | SEFAM |
|---|---|
| Model | DreamStar Series |
| Category | Humidifier |
| Language | English |
Warnings and precautions to ensure safe use and prevent patient injury or device damage.
Describes the device's purpose for non-invasive ventilation for specific patient conditions.
Lists pre-existing pathologies for which positive pressure therapy is not recommended.
Details the approved accessories that can be used with the DreamStar™ product range devices.
Explains the heated humidification feature for Evolve models and how to enable it.
Allows patients to adjust prescribed pressure by ± 1 cmH2O, applicable in CPAP mode.
Automatically starts treatment without pressing the On/Off button.
In BiLevel mode, this feature adapts settings and displays session data.
Device switches to low power if the mask is disconnected; restores power upon reconnection.
Allows gradual pressure rise to help the patient sleep, adjustable in CPAP and BiLevel modes.
Feature to remind patients about filter changes, inspections, and data downloads.
Explains key terms like backup frequency, comfort pressure, IPAP, EPAP, and ramp time.
Details default, minimum, and maximum values for parameters in CPAP and Bi-Level modes.
Overview of features like Humidifier, Pressure Alter, Auto ON, and reminders, with their enabled/disabled status.
Details device configuration based on patient circuit and water chamber accessory use.
Explains how to navigate the device settings and service menus using the control buttons.
Explains the layout of device screens, including headers, parameter lines, and symbols.
Explains the meaning of various symbols found on the device and its packaging.
Instructions on how to access the device's Settings and Service menus.
Details how to navigate and adjust settings within the CPAP mode of the device.
Details how to navigate and adjust settings within the BiLevel mode of the device.
Procedure for calibrating the device based on the patient circuit configuration.
Instructions for accessing the Service menu to select language and set the clock.
Procedure for setting the device's date, only possible when the device is in standby.
Allows enabling/disabling patient access to language, ramp time, and comfort pressure settings.
Enables or disables features like Auto ON, external module connection (Ext.), and Humidifier.
Sets reminder frequencies for filter, mask, service, and memory card usage.
Adjusts pressure offset and unit of measurement (cmH2O or hPa) for the device.
Instructions on how to access the device's Settings and Service menus.
Details how to navigate and adjust settings within the CPAP mode of the device.
Details how to navigate and adjust settings within the BiLevel mode of the device.
Explains settings for Backup Frequency, I/E Ratio, and Pressure Rise Time in BiLevel mode.
Explains settings for Inspiratory/Expiratory Sensitivity in BiLevel mode.
Details settings for Comfort Pressure and Ramp Time in BiLevel mode.
Procedure for calibrating the device based on the patient circuit configuration.
Instructions for accessing the Service menu to select language and set the clock.
Procedure for setting the device's date, only possible when the device is in standby.
Allows enabling/disabling patient access to language, ramp time, and comfort pressure settings.
Enables or disables features like Auto ON, external module connection (Ext.), and Humidifier.
Sets reminder frequencies for filter, mask, service, and memory card usage.
Adjusts pressure offset and unit of measurement (cmH2O or hPa) for the device.
Displays device operating time, total usage, and session history.
Instructions for adjusting the heated humidifier level via the device interface.
Allows confirmation or dismissal of expiring patient reminders.
Procedure for calibrating the device based on specific patient circuit and pneumatic configurations.
Instructions for data backup and machine settings update using a memory card.
Describes how devices are set via DreamStar Analyze software and memory cards.
Configuring and using a memory card as a service card for device default settings.
Instructions for daily cleaning of the water chamber.
Procedure for weekly disassembly and cleaning of the water chamber.
Instructions for washing and maintaining the washable air intake filter.
Guidelines for monthly cleaning of the device, air intake filters, and water chamber.
Methods for disinfecting the exterior of the device using spray or disinfectant towels.
Detailed steps for pre-disinfection, cleaning, disinfection, drying, and storage of the water chamber.
Lists cleaning agents and methods that should not be used on the device.
Explains device messages like MASK UNPLUGGED, HIGH FREQUENCY, and LEAK.
Provides codes (Er 01, Er 02) and corrective actions for device errors.
Details error codes (Er 03-Er 101) and their corrective actions.
Lists humidifier-related error codes (Er 102-105) and their corrective actions.
Specifies performance metrics like pressure range, accuracy, ramp duration, and backup frequency.
Details humidifier performance metrics like humidification rate and heating time.
Specifies pressure, temperature, and humidity ranges for device operation.
Details pressure, temperature, and humidity ranges for transport and storage.
Lists input voltage, power consumption, and DC power supply specifications.
Provides dimensions, weight, and water chamber volumes for the device.
Explains the meaning of various symbols found on the device and its packaging.
Indicates compliance with European Directive 93/42/EC on medical devices.
Lists standards and directives the DreamStar™ product range complies with.
Provides guidance on the environmentally responsible disposal of the device.
Details static and dynamic pressure stability compliance with ISO 17510-1:2007.
Presents maximum flow data according to ISO 17510-1:2007, Appendix CC.1.
Illustrates the airflow path and components of the DreamStar™ device.
Details electromagnetic emissions and immunity requirements for device operation.
Covers magnetic fields and conducted/radiated RF immunity requirements.
Provides guidance on maintaining safe distances from RF transmitting equipment.
Lists compliant cables and warns against using non-specified accessories.
To Next Page
