Servomex SERVOTOUGH 1900 Digital - User Manual

90 pages

Save Page as PDF

To Next Page

Part Number: 01910001A

Revision: 1

Language: UK English

Operator Manual

SERVOTOUGH 1900 Digital

Gas Analyser

PROCESS ANALYSERS

Main Page

Table of Contents5
Description and Definitions9
Scope of this Manual9
Safety Information9
Description9
Construction10
Analyser Options10
Specification15
General15
Sample Gas15
Calibration Gases16
Environmental Limits16
Electrical Data17
Performance18
Hazardous Area Certification19
Unpack the Analyser21
Analyser User Interface22
Introduction22
Start-Up and Measurement Screens22
Soft Key Legends23
Status Icon Bar24
Scroll Bars24
Menu Options/Screens and Password Protection25
The Menu Screen27
The Settings Screen28
The Information Screen28
Editing On-Screen Data29
Installation and Set-Up30
Mechanical Installation30
Remove the Power/Interface Compartment Cover32
Electrical Supply and Interface Signal Connections32
Electrical Safety32
Configure the Cable Entry Hole(S)33
Interface Signal Connections34
Mains Electrical Supply Connection35
Refit the Power/Interface Compartment Cover36
External Earth (Ground) Connection36
Connect the Sample/Calibration Gas Pipe(S)37
Switch On/Set-Up38
Selecting the Security Level and Changing the Password(S)38
Setting the Clock41
Changing Regional Settings42
General Operation43
Calibrating the Analyser43
Taking Sample Readings44
Selecting Display Units45
Configuring the Measurement Alarms47
Alarm Modes and Levels47
Latching/Non-Latching Alarms47
Hysteresis Levels48
Setting the Measurement Alarm Levels and Modes49
Unlatching Measurement Alarms50
Viewing the Measurement Alarm Status50
Configuring and Using the Milliamp Output51
Overview51
Introduction to the Milliamp Output Parameters52
Setting up the Milliamp Output Parameters53
Selecting the Range Associated with a Measurement54
Calibrating the Milliamp Output55
Checking the Milliamp Output56
Checking the Relay Signal Outputs57
Adjusting the Display58
Adjusting the Backlight Timer58
Adjusting the Contrast59
Switching off the Analyser59
Routine Maintenance60
Cleaning the Analyser60
Replacing the Inlet Filter61
Inspecting/Replacing the Fuse (When Necessary)62
Removing the Cover and Replacing the Fuse62
Refitting the Cover63
Use of the Analyser with Toxic Gases64
Preventative Maintenance65
Fault Finding66
Introduction to Faults and Fault Messages66
Viewing Fault Messages68
General Fault Finding68
Storage and Disposal72
Storage72
Disposal72
Spares73
A1 Display Unit Conversion Factors74
A2 Panel Mounting the Analyser75
A2.1 Introduction75
A2.2 Unpacking75
A2.3 Fit the Analyser with the Mounting Kit75
Materials in Contact with Sample and Calibration78
Gases78
Product Disposal/Applicability of the Waste79
Electrical and Electronic Equipment (Weee)79
Directive 2002/96/Ec79
A5 Compliance and Standards Information81
A6 Atex Certificates82

Need help?

Do you have a question about the Servomex SERVOTOUGH 1900 Digital and is the answer not in the manual?

Servomex SERVOTOUGH 1900 Digital Specifications

General

Brand	Servomex
Model	SERVOTOUGH 1900 Digital
Category	Measuring Instruments
Language	English

Related product manuals

Servomex SERVOTOUGH Oxy

145 pages

SERVOTOUGH OxyExact 2200 Series

80 pages

SERVOTOUGH SpectraExact 2500 Series

99 pages

Servomex SERVOPRO

212 pages

Servomex SERVOPRO FID

67 pages

Servomex SERVOPRO 4100

74 pages

Servomex SERVOPRO Plasma

82 pages

Servomex SERVOFLEX MiniMP

104 pages

Servomex SERVO PRO 14440D1

38 pages

Servomex SERVOPRO MultiExact

145 pages

Servomex SERVOPRO 4000 Series

74 pages

Servomex 1100A

236 pages

Servomex SERVOTOUGH 1900 Digital - User Manual

Table of Contents

Servomex SERVOTOUGH 1900 Digital Specifications

Related product manuals