What to do if SEW-Eurodrive DCA63/DBC00 motor does not respond?
If the SEW-Eurodrive DC Drives motor does not respond and is not ready, several factors could be at play. Check the U DC48V and undervoltage, and adjust if necessary. Ensure a DC 24 V supply for U DC24V. Verify that the acknowledgment is present and acknowledge if it's missing. Also, check for and correct any incorrect parameters.
Why SEW-Eurodrive DCA63/DBC00 motor regulates to 0?
If the SEW-Eurodrive DC Drives motor regulates to 0 and the set-point speed cannot be specified, it could be due to a missing setpoint. Make sure to specify the setpoint. Another reason could be an incorrectly selected setpoint, which you should rectify. Finally, verify and correct any incorrect parameters.
How to fix SEW-Eurodrive DCA63/DBC00 DC Drives motor not positioning itself?
If the SEW-Eurodrive DC Drives motor does not position itself, ensure that IN A/IN B is set to 1/1 to enable it. Adjust KP_H if it is missing. Also, adjust the maximum positioning speed if it is set to 0. If no distance is set, set it or use teach mode.
Why does my SEW-Eurodrive DCA63/DBC00 DC Drives motor judder?
If the SEW-Eurodrive DC Drives motor judders, it might be due to an unsuitable control parameter, so adjust it. Also, adjust the position controller. Check if K_FF is unsuitable and adjust it if needed. If U DC48V fluctuates, stabilize it.
How to improve dynamics of SEW-Eurodrive DC Drives motor?
If the SEW-Eurodrive DC Drives motor exhibits weak dynamics, consider the following: * Configure the motor if it is overloaded. * Set a steeper ramp if the current ramp is too flat. * Open current limiting if it is active.
What to do if SEW-Eurodrive DC Drives motor judders on position hold?
If the SEW-Eurodrive DC Drives motor judders when switching to position hold control, it may be because K_FF is set to 0. Set K_FF to resolve this issue.
Why SEW-Eurodrive DCA63/DBC00 motor coasts to halt when braking?
If the SEW-Eurodrive DC Drives motor coasts to a halt when braking, it could be due to overvoltage. In this case, use a feedback protected power supply unit. Alternatively, use a braking resistor.
General| Brand | SEW-Eurodrive |
|---|---|
| Model | DCA63/DBC00 Series |
| Category | DC Drives |
| Language | English |
Details the original documentation, its purpose, and intended audience.
Explains signal word grading and the structure of safety notes.
Outlines user responsibilities for safe operation and maintenance.
Specifies the intended application and restrictions for the product.
Provides guidelines for proper installation and assembly.
Describes the features and construction of the DCA63../DBC00 drive unit.
Presents a table of technical specifications for different motor power ratings.
Illustrates typical nameplates and explains type designation codes.
Details the procedures and precautions for installing the drive unit.
Shows connector locations and installation clearance for different gear units.
Provides guidance on arranging components and applying motor shields for EMC.
Illustrates principle line and star topologies for drive connection.
Details motor connection plug information and connection cable specifications.
Outlines the steps and required components for starting up the drive.
Explains available operating modes: Speed Control, Positioning, Absolute Positioning.
Describes how to configure analog input for speed and position setpoints.
Explains how to view drive status, fault memory, and record values.
Details how to read and modify operating mode parameters.
Guides on using the manual mode for testing drive functions.
Lists and explains various configurable parameters for the drive.
Provides detailed explanations for specific parameters like digital outputs and speed settings.
Details internal functions for temperature, voltage, and current monitoring.
Explains how to acknowledge error messages and reset the drive.
Describes the function and structure of the engineering adapter.
Lists common malfunctions, their causes, and remedies.
Guides on interpreting error messages using the DCAShell software.
Provides instructions for replacing a drive unit, including safety notes.
Outlines recommended intervals and activities for motor inspection.
Lists required data points for selecting the appropriate drive components.
Illustrates the step-by-step process for planning a drive application.
Covers dimensioning of DC 24 V and DC 48 V supplies and regenerative operation.
Explains conditions and parameter adjustments for reduced voltage operation.
Presents comprehensive technical specifications for the drive.
Provides detailed dimensional drawings for various drive configurations.
Includes the UL Certificate of Compliance for the product.
To Next Page