Shark S7201 Series User Manual

NOTE: To prolong the life of your steam mop, we recommend using distilled water.
NOTE: If the handle is not reclined the pads do not spin.
NOTE: Sweep or vacuum your floors prior to cleaning with your steam mop.
NOTE: Both pads must be installed at all times during use.
TO SANITISE*:
1 Attach clean Dirt Grip pads to the scrubbing nozzle.
2 Plug in the unit, tilt the mop handle down towards you, and press the mode button to select
the DEEP setting. The pads will then start spinning.
3 Wait 30 seconds for the unit to begin producing steam.
4 Start mopping with a forward and backward motion on an appropriate sealed hard floor
surface. After three minutes, your unit will be ready to sanitise.
5 Using a forward and backward motion, move the unit slowly and evenly over the area to be
sanitised while applying continuous downward pressure. Slowly repeat at least 8 times.
*Sanitisation studies were conducted under controlled test conditions. Household
conditions and results may vary. With scrubbing nozzle in DEEP mode.
STEAM BLASTER:
1 To target tough messes with an extra burst of cleaning
power, move the front of the nozzle 2 to 4 inches from
the mess then press and hold the Steam Blaster button as
needed. Hold longer for the toughest messes.
2 Before scrubbing, wait 5 seconds to let the steam blast
penetrate the mess.
1
3
2
1 Make sure that your pads are secured to
the nozzle discs.
Twist the quick-release cord holder
to unwrap the power cord completely.
Plug into an electrical socket.
2 When it's first plugged in, the unit will be
in Standby mode. The 3 settings will blink
to indicate Standby mode.
Please note, if the handle is not reclined
with in 30 seconds of selecting a mode
the mop goes back into standby.
3 To select the steam mode, press
the mode button. Once the mode is
selected, tilt the handle down to activate
the spinning pads.
4 Mop with a forward and backward motion.
5 When the water tank is empty, the steam
mop will stop producing steam. Make sure
the unit is unplugged before refilling the
water tank.
6 When finished mopping, press the mode
button until you've reached Standby
mode. The settings lights will blink,
indicating that the unit is in Standby mode.
Once in Standby mode, lift the handle to
bring the steam mop back to the upright
position and unplug the unit.
7 Please wait 2 to 3 minutes for the steam
mop to cool completely before removing
the Dirt Grip pads.
Never leave the steam mop with damp
or wet Dirt Grip pads on any floor for an
extended period.
TIP: When cleaning near skirting boards,
edges or furniture, you may feel a slight pull
from the unit making contact with surfaces.
This is normal and not a cause for concern.
The Shark
®
Steam & Scrub Steam Mop has 3 unique Intelligent Steam Control settings so you
can select the ideal amount of steam to use for each cleaning task. In NORMAL mode, the pads
will spin faster and more steam will be produced than in LIGHT mode. In DEEP mode, the pads
will spin the fastest and the maximum amount of steam will be produced. See below for tips on
when to use each setting.
SETTING IDEAL FOR THESE
SEALED SURFACES
RECOMMENDED USAGE
LIGHT
Laminate
Hardwood
Vinyl
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
NORMAL
Marble
Tile
Stone
Basic, everyday cleaning
Cleaning large areas
Cleaning moderate and heavy trac areas
DEEP
Marble
Tile
Stone
Reaching hard-to-clean surfaces
Tough cleaning and removing stuck-on
messes and stains
Deep cleaning heavy trac areas
Cutting through heavy dirt and grime
Sanitising* floors
8sharkclean.co.uk7 sharkclean.co.uk
USING YOUR STEAM AND SCRUB MOP INTELLIGENT STEAM CONTROL™

Shark S7201 Series Specifications

General

Brand	Shark
Model	S7201 Series
Category	Steam Cleaner
Language	English