In this example, the clock is set for the
24-hour
(0:OO)
system.
TUNlNGfllME
(V/A
1
*
I
\\‘I/
I-
I
I-II-
1-f
I_ I_
l-l
I_
I
’
I/
I
\’
3
I
\\‘I/
t-1
4-t
t-t
I-J-U
I-J
/I
I
\’
\\I’/
1-r
4-1
t-r
IJu
u
/I
I
\’
AM 12:OO
++AM
0:OO
-
0:OO
t
t
\
I
/
r-1
.I-11-r
I-ILI
I-l
1
I
\
6
I
\
I
f
I
t-t-l-l
r-1
I
u
LJ
IJ
f
I
\
\
I
/
I
I-In
r-1
I
I_lLl
I-1
f
I
\
8r
\
I
/
I
1-i
*
7
1-1
I
l._l~~,f~
9
71
1
2
3
4
5
6
0
0
7
8
l
l
9
l
Set the ON/STAND-BY switch to STAND-BY.
Press the CLOCK button.
Within 3 seconds, press the MEMORY/SET button.
Press the TUNINGfllME
(v
or A) button to select the time
display.
“AM 12:OO”
+
The
12-hour
display will appear.
(AM 12:00
-
PM
1159)
“AM
0:OO”
+
The
12-hour
display will appear.
(AM
0:OO
-
PM
1159)
“0:OO”
+
The
24-hour
display will appear.
(0:OO
-
2359)
Press the MEMORY/SET button.
Press the TUNING/TIME
(V
or A) button to adjust the hour.
Press the TUNING/TIME button once to advance the time by
1 hour. Press for more than 0.5 seconds to advance continu-
ously.
When the
12-hour
display is selected, “AM” will change auto-
matically to “PM”.
Press the MEMORY/SET button.
Press the TUNING/TIME
(V
or
A)
button to adjust the
minutes.
Press the button for at least 0.5 seconds to change the time
in 5 minute intervals.
The hour setting will not advance even if minutes advance
from “59” to
“00”.
Press the MEMORY/SET button.
The clock starts operating from
“0”
seconds. (Seconds are
not displayed.)
Note:
l In the event of a power failure or when the AC power lead
is disconnected, the clock display will go out.
When the AC power supply is restored, the clock display will
flash on and off to indicate the time when the power failure
occurred or when the AC power lead was disconnected.
If this happens follow the procedure below to change the clock
time.
To change the clock time:
When the ON/STAND-BY switch is set to STAND-BY.
0
Press the MEMORY/SET button.
Q
Perform steps 6
-
9 above.
When the ON/STAND-BY switch is set
t’;
ON.
0
Press the CLOCK button.
Q
Within 3 seconds, press the MEMORY/SET button.
0
Perform steps 6
-
9 above.
To see the time display: (When the power is ON)
Press the CLOCK button.
l
The time display will appear for about 3 seconds.
To switch the time display mode:
1
Set the ON/STAND-BY switch to STAND-BY.
2
Press and hold down the VOLUME
\;/
button, the
FF
/
Hi
button and the ON/STAND-BY switch all at the same time.
Hold them for at least 1 second.
3
Perform steps 1
-
9 above.
Note:
l
The operation explained above will erase all data stored in
memory, such as clock and timer settings, tuner and CD pres-
ets.
9
I
-
To Next Page
Loading...
Need help?
General
