Optional System (Continued)
ATV/�TV/RA�IO . buttons
Convert analog audio format
NTSC . broadcast signal
Enter language
Use the following buttons on the remote control to
control the menu.
You can switch between multi-channel audio
modes when watching a program with stereo or
multi-channel sound.
When receiving a Dual Audio signal +SAP
Every time you press the . keyMPX, the modes will be
switched between ST (SAP), SAP (ST) and MONO.
Choose from 5 languages: Eastern European, Western European,
Cyrillic, Arabic and Persian.
ATV/�TV:Press to switch between ATV and DTV
modes. After switching from ATV or DTV, radio mode
or external input mode to ATV and DTV mode, the TV
jumps to the most recently viewed ATV and DTV
channel.
Dual sound mode + SAP
PAL . broadcast signal
ATTENTION
ST (SAP)
SAP (ST)
•
Teletext can only be displayed when sent by a network.
Not used to switch between languages.
In the NICAM . system broadcast
When receiving a dual audio signal
Every time you press the . keyMPX, the modes will be
switched between DOUBLE SOUND NICAM and MONO.
MONO
HExperimental (For display mode only)
display)
When “Display Mode” is set to “On”, after
completing all the settings, the Feature Test screen
will be displayed if there is no operation for 30
seconds.
RA�IO:Press to switch from DTV to radio mode. The TV
will jump to the most recently tuned radio station.
When receiving signalmono + SAP
Every time you press the . keyMPX, modes will be
switched between MONO and SAP.
When watching TV for the first time
When turning on the TV for the first time after purchase, perform the
installation automatically.
Dual sound mode
DOUBLE SOUND NICAM MONO
MONO + SAP . mode
MONO SAP
Program Guide
When receiving a bilingual signal
Every time you press the . keyMPX, the modes are switched in
sequence NICAM DOUBLE I, NICAM DOUBLE II, NICAM DOUBLE I
+ II and MONO.
ATV (Analog TV)
You can run auto setup to set up channels
automatically.
When receiving a dual audio signal
Every time you press the . keyMPX, the modes will be
switched between DOUBLE SOUND and MONO.
You can check the current channel list of DTV/
ATV respectively.
first
2
3
first
To watch analog TV, select “ATV” from “Type
Search” in Auto Setup Driver. (See page 12.)
Bilingual mode
Dual sound mode
PressGUI�E(MANUAL) to display the program
channel list.
NICAM DOUBLE I NICAM DOUBLE II
DOUBLE SOUND MONO
Pressa/bto select the desired programme, and
then pressENTER(ENTER).
2
After setting up channels, you can select
channels throughONLYr/sor0 – 9on the
remote control. (See page 9.)
ATTENTION
•
On-screen display in this manual is for explanation only
and may differ slightly from actual screen display.
PressRETURN(BACK) orGUI�E
(TUTORIAL) to exit.
MONO NICAM DOUBLE I + II
DTV (Digital TV)
When the TV enters DTV mode for the first time,
you need to run auto search. To scan all available
services in your area, follow the procedure below.
When receiving a mono . signal
Every time you press the . keyMPX, the modes will be
switched between NICAM MONO and MONO.
Information
Mono mode
While watching DTV, you can check the extended
program information on the screen by using the .
buttonINFOon the remote control.
first
NICAM MONO MONO
To view broadcasts by DTV system, select “DTV”
from “Type Search” in Auto Setup Driver. (See
page 12.)
General INFO (Information) screen
In the mode where signal A2 is transmitted
•
Station name
•
Title
•
Day
•
Time for the current program
•
Year old
•
Category
•
Program Information
2
After setting up channels, you can select
channels throughONLYr/sor0 – 9the remote
controller. (See page 9.)
When receiving a dual audio signal
Every time you press the . keyMPX, the modes will be
switched between DOUBLE SOUND and MONO.
Dual sound mode
DOUBLE SOUND MONO
When receiving a bilingual signal
Every time you press the . keyMPX, the modes are switched in
the sequence DOUBLE I, DOUBLE II and DOUBLE I + II.
ATTENTION
•
If there is more information, pressa/ballows you to go
to the next page or return to the previous page.
•
You can cancel this information by pressing the . button again
INFO
Bilingual mode
DOUBLE I
DOUBLE II
DOUBLE I + DOUBLE II
21 22
To Next Page
Loading...
