Sharp AR-M201 Service Manual (English)

Other manuals for Sharp AR-M201

Service Manual176 pages

Operation Manual96 pages

Questions and Answers:

L
larry93Aug 23, 2025
What to do if my Sharp Copier is not printing after selecting it?
- M
  mjacobsAug 23, 2025
  If your Sharp Copier isn't printing even after you've selected it in the print window, the issue might be that the printer driver hasn't been installed properly. To resolve this, check the printer driver installation by going to the Control Panel, then to Printers and Other Hardware, and finally to Printers and Faxes. See if the "SHARP AR-XXXX" printer driver icon is there. If it is, but you still can't print, try deleting the existing driver and reinstalling it.
T
Terry MartinezAug 25, 2025
What to do if my Sharp AR-M201 Copier is not printing due to paper size?
- M
  Molly OneillAug 25, 2025
  If your Sharp Copier isn't printing and you suspect it's related to paper size, there are a few things to check: * First, make sure that the size of paper loaded in the tray and the machine's paper size setting agree. * Second, if the specified size of paper has not been loaded, load the specified size of paper in the paper tray. * Finally, when "FORCED OUTPUT" is set to "OFF" and there is no paper in the machine that is the same size as the print image, load paper in the bypass tray as instructed by the message in the display and press the [START] key to begin printing.
M
Molly HerreraAug 26, 2025
What does 'TONER CARTRIDGE IS NEAR EMPTY' mean on Sharp Copier?
- A
  asmithAug 26, 2025
  If your Sharp Copier displays 'TONER CARTRIDGE IS NEAR EMPTY', it means that you should prepare a new cartridge.
A
Alexander AtkinsAug 27, 2025
What to do if Sharp Copier does not print because of a copy job?
- L
  lisa26Aug 27, 2025
  If your Sharp Copier is not printing, it may be because a copy job is currently in progress. Wait until the copy job is finished before attempting to print.
R
rodriguezmelissaAug 29, 2025
Why my Sharp Copier does not operate?
- J
  Jonathan SmithAug 29, 2025
  If your Sharp Copier is not operating, consider the following possibilities: 1. Ensure the machine is plugged into a grounded outlet. 2. Check that the power switch is turned ON. 3. If the power save indicator is blinking, allow the machine to finish warming up. 4. Make sure the front cover or the side cover is completely closed. 5. If the machine is in auto power shut-off mode (only the power save indicator is lit), press the [START] key to resume normal operation.
M
Michelle CrawfordAug 31, 2025
What to do if Sharp Copier says 'FRONT OR SIDE COVER OPEN'?
- L
  Linda MarshAug 31, 2025
  If your Sharp Copier displays 'FRONT OR SIDE COVER OPEN. CLOSE COVERS', it means the cover is open. Ensure that you close the cover.
R
Ryan SellersSep 1, 2025
Why are Sharp AR-M201 Copier copies too dark or too light?
- X
  xfuentesSep 1, 2025
  If copies from your Sharp Copier are too dark or too light, select AUTO with the [EXPOSURE] key, or manually adjust the exposure using the [ ] or [ ] keys. If AUTO was selected, you may also need to adjust the automatic exposure level.
T
Tyler MitchellSep 3, 2025
Why Sharp AR-M201 Copier makes blank copies?
- J
  James PayneSep 3, 2025
  If your Sharp Copier is producing blank copies, make sure you're placing the original face up in the RSPF or face down on the document glass.
P
Patrick FordSep 4, 2025
What does 'LOAD XXXX PAPER INTO TRAY' mean on Sharp AR-M201 Copier?
- S
  sramirezSep 4, 2025
  If your Sharp Copier displays 'LOAD XXXX PAPER INTO TRAY', it means the paper size setting doesn't match the paper loaded in the tray. Load paper that matches the size setting, and then press the [START] key.
K
Kayla PerezSep 6, 2025
Why is the image cut off on Sharp AR-M201 Copier?
- W
  whughesSep 6, 2025
  If the image is cut off or there's too much blank space when using your Sharp Copier, consider these solutions: 1. Ensure the original is placed correctly. 2. Adjust the ratio using the [COPY RATIO] key to suit the original and paper sizes. 3. If you changed the paper size in the tray, remember to update the tray's paper size setting accordingly.