Sharp AR-M350U

AR-M350 SIMULATIONS 10-10
<List of set values>
<List of display values>
2-3
Purpose Operation test, check
Function (Content) Used to check the operation under load in the
automatic document feeder unit and their control
circuits.
Section DSPF
Item Operation
Operation/Procedure Select with 10 digit key pad.
1 Motor high speed rotation
2 Motor low speed rotation
3 Document stopper solenoid
4 Document feed solenoid
5 Document feed clutch
6 Document resist clutch
7 Stamp solenoid
SIMULATION 2-3
SPF LOAD TEST. SELECT 1-7, AND PRESS START.
1. MOTOR(H) 2. MOTOR(L)
3. SDSS 4. SPFS 5. SPFC 6. SPSC 7. STMPS
2
SIMULATION 2-3
SPF LOAD TEST. EXECUTING...
1. MOTOR(H) 2. MOTOR(L)
3. SDSS 4. SPFS 5. SPFC 6. SPSC 7. STMPS
2
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
Main code 3
3-2
Purpose Operation test, check
Function (Content) Used to check the operations of the sensors and
detectors in the finisher and their control circuits.
Section Finisher
Item Operation
Operation/Procedure The display is highlighted when detected.
Finisher Console finisher
STHP Stapler HP detection FSSS Stapler safety switch
POD Tray 2 paper exit detection FJS Joint switch
SCID Staple compiler paper entry
detection
FFDSW Front door switch
PID Paper entry detection FTCS Upper cover sensor
T2PD Tray 2 paper empty detection FFDS Front door sensor
T2DN Tray 2 lower limit detection FSPS Self prime sensor
T2UP Tray 2 upper limit detection FSUC Stapler connection detection
JRHP Jogger R HP FSS Staple sensor
JFHP Jogger (F) HP FSTHPS Stapler HP sensor
SCID2 Staple compiler paper entry
detection 2
FSHPS Slide HP sensor
STTHP2 Staple rotation HP detection 2 FLE Lift lock sensor
STTHP1 Staple rotation HP detection 1 FLLLS Lift lower limit sensor
STUHP Staple shift HP detection FULS Lift upper limit sensor
PSHP Pusher HP detection FFE Bookbinding clock sensor
PPD Paper hold return detection FFES Bookbinding paper sensor
DSW2 Staple replacement door open
detection
FFRHPS Bookbinding roller HP sensor
DSW1 Compiler jam cancel door open
detection
FFHPS Bookbinding HP sensor
24VM 24V power supply FFPS Bookbinding position sensor
T1PF Tray 1 full detection FSLS Paper surface sensor
STSP Stapling ready detection FBES Tray paper sensor
STLS Cartridge inside spare staple
empty detection
FOBHPS Paper exit belt HP sensor
STNC Cartridge empty detection FAS Alignment tray sensor
DOPD Interface unit door open
detection
FRJHPS Alignment HP sensor R
MMLK Main drive motor lock detection FFJHPS Alignment HP sensor F
SCPD Staple compiler paper empty
detection
FARHPS Bundle roller HP sensor
FPHPS Paddle HP sensor
FES Entry port sensor
SIMULATION 3-2
FINISHER SENSOR CHECK.
PID SCID SCID2 PPD
SCPD POD T1PF T2UP
T2DN T2PD STSP STLS
STNC STHP JFHP JRHP
PSHP STUHP XXXX STTHP1
STTHP2 DOPD DSW1 DSW2
24VM MMLK
Finisher (AR-FN6)
Console finisher (AR-FN7)
SIMULATION 3-2
FINISHER SENSOR CHECK.
FSSS FJS FFDSW FTCS FFDS
FSPS FSUC FSS FSTHPS FSHPS FLE FLLLS
FULS FFE FFES FFRHPS FFHPS FFPS FSLS
FBES FOBHPS FAS FRJHPS FFJHPS FARHPS FPHPS
FES
(FPE) (FPSHPS) (FPUC) (FPDS) (FPDSS4) (FPDSS3) (FPDSS2)
(FPDSS1) (FPTS)
Devices in ( ) are added when the punch unit is installed.
        !"# $%&