AR-M350 SIMULATIONS 10-11
•The following units are added when the punch unit is installed to the
console finisher:
<List of display values>
(Stored on PCU PWB)
<List of set values>
(Values stored in EEPROM)
FPE Punch motor encoder
FPSHPS Punch side register HP
FPUC Punch connection detection
FPDS Punch dust sensor
FPDSS4 Punch side register sensor 4
FPDSS3 Punch side register sensor 3
FPDSS2 Punch side register sensor 2
FPDSS1 Punch side register sensor 1
FPTS Punch timing sensor
3-3
Purpose Operation test, check
Function (Content) Used to check the operation under load in the
finisher and their control circuits.
Section Finisher
Item Operation
Operation/Procedure The display is highlighted when detected.
Finisher Console finisher
1 T2S Tray 2 solenoid 1 FFC Folding clutch
2 T2OM Paper exit motor 2 FPSM Puncher side register
motor
3 SPS Stopper solenoid 3 FPNM Punch motor
4 SCRS Roller pressure
release solenoid
4 FLM Shift motor
5 PPS Rear edge h folding
solenoid
5 FFSM Stapler motor
6 SCGS Compiler gate
solenoid
6 FSM Slide motor
7 STTM Staple rotation motor 7 FRJM Alignment motor R
8 STUM Stapler shift motor 8 FFJM Alignment motor F
9 MM Main drive motor 9 FAM Bundle exit motor
10 EVM Elevator motor 10 FPM Paddle motor
11 STM Staple motor 11 FFM Transport motor
12 JRM Jogger motor rear
13 JFM Jogger motor front
14 PSM Pusher motor
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1- , AND PRESS START.
2
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING...
2
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
3-6
Purpose Adjustment
Function (Content) Used to adjust the stacking capacity of the
finisher (AR-FN6). (Used to adjust the alignment
plate (jogger) stop position in the finisher paper
width direction. The adjustment is made by
changing the alignment plate home position in
the paper width direction by software. )
Section Finisher
Item Operation
Operation/Procedure Enter the adjustment value with 10 digit key pad
and press START key. The jogger moves to LT
position (Inch series) or A4 position (AB series)
according to the entered value, and stops there.
3-10
Purpose Adjustment
Function (Content) Used to adjust the console finisher (AR-FN7).
Section Finisher
Item Operation
Operation/Procedure Setting of the console finisher is performed.
Adjustment content Range
Initial
value
1STEP
1 Saddle binding position adjustment 0~400
200
0.0707mm
2 Saddle folding position adjustment 0~400
200
0.0525mm
3 Front alignment position adjustment 0~20
10
0.367mm
4 Rear alignment position adjustment 0~20
10
0.367mm
5 Staple rear one-position binding position adjustment 0~200
100
0.04374mm
6 Staple front one-position binding position adjustment 0~200
100
0.04374mm
7 Staple 2-position binding center adjustment 0~200
100
0.04374mm
8 Staple 2-position binding pitch adjustment 0~99
50
0.04374mm
9 Punch center adjustment (Slide direction) 47~53
50
1mm
10 Punch hole position adjustment (Paper feed direction) 0~99
50
0.105mm
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
50
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. MOVING...
50
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
Stops when the operation is terminated.
SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10, AND PRESS START.
1. SADDLE POSITION 2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST 5. STAPLE REAR
6. STAPLE FRONT 7. STAPLE BOTH
8. STAPLE PITCH 9. PUNCH CENTER
10. PUNCH HOLE
1
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1. FOLDING POSITION
200
Press [START] key to get started.
Press [CUSTOM SETTING] key to stop.
!"# $%&
To Next Page
Loading...
