Sharp AY-X36RU User Manual (English)

Other manuals for Sharp AY-X36RU

Operation Manual48 pages

Service Manual46 pages

Questions and Answers:

J
Joseph SmithJul 31, 2025
What does it mean when the outdoor ambient temperature sensor is open/short circuited in Sharp AY-X36RU Air Conditioner?
- M
  mitchelljodiJul 31, 2025
  If the outdoor ambient temperature sensor is open or short-circuited in your Sharp Air Conditioner, it might be because the sensor isn't connected properly or is damaged. Check it using the resistance table for the temperature sensor. During cooling and drying, the compressor will stop, but the indoor fan will keep running. During heating, the entire unit will stop.
T
Tracy WhiteAug 4, 2025
What causes an open or short circuited outdoor condenser temperature sensor in a Sharp AY-X36RU Air Conditioner?
- C
  Caroline SmithAug 4, 2025
  If the outdoor condenser temperature sensor is open or short-circuited in your Sharp Air Conditioner, it may be due to the outdoor temperature sensor not being connected well or being damaged. Check it by referring to the resistance table for the temperature sensor. During cooling and drying, the compressor will stop, but the indoor fan will operate. During heating, the entire unit will stop operating.
B
barrjamieAug 8, 2025
Why does my Sharp AY-X36RU Air Conditioner have high pressure protection?
- D
  Dawn LoveAug 8, 2025
  The Sharp Air Conditioner system might have high pressure protection due to several reasons: * Too much refrigerant. * Poor heat exchange because of a blocked heat exchanger or a bad radiating environment. * Ambient temperature being too high. During cooling and drying, only the indoor fan will work, and other components will stop. During heating, the entire unit will stop. Also, ensure the supply voltage is within the normal range.
V
valdezrachaelAug 13, 2025
Why is the voltage for DC bus-bar too high in my Sharp AY-X36RU Air Conditioner?
- L
  laceychavezAug 13, 2025
  If the voltage for the DC bus-bar is too high in your Sharp Air Conditioner, it could be due to: * The voltage at positions L and N on the wiring board (XT) being higher than 265VAC. In this case, turn on the unit after the supply voltage is normal. * If the AC input is normal, but the voltage of the electrolytic capacitor C on the control panel (AP1) is not, then the circuit is malfunctioning and the control panel (AP1) should be replaced. During cooling and drying, the compressor will stop, but the indoor fan will keep running. During heating, the entire unit will stop.
J
Joshua WhiteAug 17, 2025
What causes low voltage of DC bus-bar in a Sharp AY-X36RU?
- A
  Amy MullinsAug 17, 2025
  If the voltage of the DC bus-bar is too low in your Sharp Air Conditioner, it could be due to: * The voltage at positions L and N on the wiring board (XT) being higher than 150VAC. In this case, turn on the unit after the supply voltage is normal. * If the AC input is normal, but the voltage of the electrolytic capacitor C on the control panel (AP1) is not, then the circuit is malfunctioning and the control panel (AP1) should be replaced. During cooling and drying, the compressor will stop, but the indoor fan will keep running. During heating, the entire unit will stop.
R
rpatelAug 21, 2025
What causes the four-way valve to be abnormal in Sharp AY-X36RU?
- C
  Christopher BakerAug 21, 2025
  An abnormal four-way valve in your Sharp Air Conditioner can be caused by: * Supply voltage being lower than AC175V. * The wiring terminal 4V being loose or broken. * The 4V valve being damaged; it should be replaced. If this happens during heating, the entire unit will stop.
B
Becky BarberAug 27, 2025
What does malfunction of complete units current detection mean for Sharp Air Conditioner?
- R
  Rachel HaleAug 27, 2025
  A malfunction in the complete units current detection of your Sharp Air Conditioner usually means there's a circuit malfunction on the outdoor units control panel AP1, which needs to be replaced. During cooling and drying, the compressor will stop, but the indoor fan will keep running. During heating, the entire unit will stop.