Sharp GX-BT180

How to remove the battery for disposal
RISK OF INJURY. WEAR GLOVES WHEN WORKING!
The battery should be removed by an authorized Sharp service centre. Not doing
so will invalidate any guarantees and warranties on your device.
1. Use a  at screwdriver to gently prize away the fabric cover.
2. Unscrew the radiator covers at each end of the unit, 4 screws in each, 8 in total.
3. Remove the radiator covers to expose the radiator holder. Unscrew 6 screws each end,
12 in total.
(One side is screwed into place, the other side is glued into place)
4. Remove the radiator holder and to fully expose the radiator, remove the radiator by
hand. Do this for both ends of the unit. Gently pry the radiator loose.
5. Unscrew the 8 screws which hold the 2 halves of the unit together. Gently separate the
two halves being careful not to damage any wiring joining them together.
6. Inside one of the halves you will see the blue battery, it is held in place with a  xing
bracket. Unscrew the 2 bracket screws to detach the battery from the unit.
7. Disconnect the battery connector from the board and remove the battery.
Disposal of this equipment
• Do not dispose of this product as unsorted municipal waste. Return it
to a designated collection point for the recycling of WEEE in accordance
with local law. By doing so, you will help to conserve resources and
protect the environment.
• The shown above appears on electrical and electronical equipment (or the packaging)
to remind users of this.
• Users are requested to use existing return facilities for used equipment and batteries.
CE and UKCA statement:
• Hereby, Sharp Consumer Electronics Poland sp. z o.o. declares that this audio device
is in compliance with the essential requirements and other relevant provisions of RED
Directive 2014/53/EU and UK Radio Equipment Regulations 2017.
• The full text of the EU declaration of conformity is available by following the link
www.sharpconsumer.com and then entering download section of your model and
choosing “CE Statements”.
EN
What is included in the box:
• 1 x Main unit GX-BT180
• 1 x USB Cable
• 1 x AUX In Cable
• 1 x User manual
Panels & Controls
1. Power – short press to power on/off
2.
– Bluetooth Indicator
3.
– Battery Indicator
4. Aux in Jack 3.5mm – Aux in cable
supplied
5. MicroUSB Charge slot – USB cable
supplied
6.
Volume up – Short press
Skip forward button - Long press
7. ► Play/Pause – Click to play/pause,
Double Click for SIRI/GOOGLE.Click to
answer/end, Double Click to reject call.
8.
– Microphone
9.
Volume down – Short press
Skip backward button - Long press
Getting started
Power on/off
Short press
button to power on/off the
speaker.
The indicator light will  ash blue.
The speaker has a memory function and
when powered will enter the same mode
as prior to power off . Each time the speaker
powers on it will reset to 50% volume.
After 10 mins with no activity/connection
the GX-BT180 will automatically power off
to conserve battery.
Charging
Please use the supplied Micro USB cable
to charge the GX-BT180. A full charge
will take around 3 hours. Please close the
port cover after you have charged the
GX-BT180.
Modes
Bluetooth Mode
A. Pairing
Power on the speaker and enter
Bluetooth mode. The light indicator
will  ash. On your smartphone search
Bluetooth devices for the “SHARP
GX-BT180”. Once connected the
speaker will announce it is “connected”
and the indicator light will cease
 ashing.
B. Music
► Click to play/pause
Click to increase volume
press and hold for 1.5 seconds to
skip forward a track
Click to decrease volume
press and hold for 1.5 seconds to
skip back a track
C. Calls
► Click to answer an incoming call
► Click to end the active call
► Double click to reject an incoming
call or press and hold
D. SIRI/GOOGLE
► Double click to activate/cancel Siri/
Google voice dialing.
E. Disconnect
► Press and hold to disconnect the
current Bluetooth connection. The
GX-BT180 will prompt “disconnected”.
Then other Bluetooth devices can  nd
and pair with the GX-BT180.
4
7 / 70 6 / 68 7 / 70