Sharp LC-52LE640U

LC-52/60/70LE640U,C6400U (1st Edition)
4 – 17
4. Removing of 70” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER Unit.
1. Remove the 24 Hooks and detach the 70” LCD Panel Module Unit .
2. Remove the 2 Connecting Cords , 2 Ferrite Cores , 6 lock screws and detach the LCD CONTROL Unit .
3. Remove the 2 look screws and detach the 2 Spacers .
4. Remove the 6 lock screws and detach the POWER Unit .
5. Remove the 5 lock screws and detach the MAIN PWB Shield .
6. Remove the 3 lock screws and detach the MAIN Unit and Terminal Angle (Bottom) .
7. Remove the 12 lock screws and detach the 2 Support Ass’y .
8. Remove the 16 lock screws and detach the 4 VESA Angle Ass’ys .
䎔䎚
䎔䎛
䎔䎚
䎔䎚
䎔䎚
䎔䎛
䎜
䎛
䎔䎗
䎔䎖
䎔䎕
䎔䎔
䎔䎓
䎔䎙
䎔䎘
䎘
䎗
䎔䎘
䎔䎙
䎖
䎕
䎶䏘䏓䏓䏒䏕䏗䎃䎤䏖䏖䎊䏜
䎯䎦䎧䎃䎦䎲䎱䎷䎵䎲䎯䎃䎸䏑䏌䏗
䎩䏈䏕䏕䏌䏗䏈䎃䎦䏒䏕䏈
䎦䏒䏑䏑䏈䏗䏌䏑䏊䎃䎦䏒䏕䏇
䎷䏈䏕䏐䏌䏑䏄䏏䎃䎤䏑䏊䏏䏈
䎋䎥䏒䏗䏗䏒䏐䎌
䎰䎤䎬䎱䎃䎸䏑䏌䏗
䎰䎤䎬䎱䎃䎳䎺䎥䎃䎶䏋䏌䏈䏏䏇
䎹䎨䎶䎤䎃䎤䏑䏊䏏䏈
䎃䎤䏖䏖䏃䏜
䎹䎨䎶䎤䎃䎤䏑䏊䏏䏈䎃䎤䏖䏖䏃䏜
䎹䎨䎶䎤䎃䎤䏑䏊䏏䏈䎃䎤䏖䏖䏃䏜
䎳䎲䎺䎨䎵䎃䎸䏑䏌䏗
䎚䎓䎅䎯䎦䎧䎃䎳䏄䏑䏈䏏䎃䎰䏒䏇䏘䏏䏈䎃䎸䏑䏌䏗
䎔
䎫䏒䏒䏎
䎫䏒䏒䏎
䎫䏒䏒䏎
䎹䎨䎶䎤䎃
䎤䏑䏊䏏䏈
䎤䏖䏖䏃䏜
䎫䏒䏒䏎
䎙
䎚
䎙
䎚
䎔䎛
䎔䎛
䎶䏓䏄䏆䏈䏕
䎶䏓䏄䏆䏈䏕
䎶䏘䏓䏓䏒䏕䏗䎃䎤䏖䏖䎊䏜