Sharp LC-90LE657U User Manual

>>
<<
Appendix
ENG 11-7
Troubleshooting(Continue)
Problem Possible Solution
No sound Is connection to other components correct?
Is the volume too low?
Page 3-2
Is "Variable" selected in "Output Select"?
Page 4-20
Have you pressed MUTE on the remote control unit?
Page 3-3
Check the audio output of the connected external equipment. Is
the volume too low or muted?
When external equipment is connected via an HDMI cable, you
may need to configure the audio to be output through the HDMI
cable.
When audio is not output from external equipment connected to
the PC IN or HDMI IN 2 terminal, check the "Audio Select"
setting.
Page 8-2
Even when external equipment is connected using an HDMI-
certified cable, an audio cable connection may be required
depending on the type of equipment and the media being played
back. In this case, in addition to connecting an HDMI-certified
cable to the HDMI IN 2 terminal, connect a Ø 3.5 mm stereo
minijack cable to the AUDIO IN terminal and set "Audio Select" to
"HDMI+Analog".
Page 8-2
When connecting a PC via an HDMI-certified cable, check the
following:
- Is the audio output of the PC configured correctly? Check the
audio output settings and output audio format in Sound Properties
on the PC.
The audio formats compatible with this TV are PCM, Dolby Digital
and DTS. With other formats, audio cannot be output.
- Depending on the board, only video signals may be output. In
this case, in addition to connecting an HDMI-certified cable to the
HDMI IN 2 terminal, connect a Ø 3.5 mm stereo minijack cable to
the AUDIO IN terminal and set "Audio Select" to "HDMI+Analog".
Page 8-2
Problem Possible Solution
No sound If you are using a DVI-HDMI conversion cable to connect external
equipment to the TV, check the following:
- Is an audio cable connected? The DVI-HDMI conversion cable
is for video only. Connect a Ø 3.5 mm stereo minijack cable to
listen to the audio.
- Is HDMI IN 2 being used? When the TV is connected to another
HDMI IN terminal, the audio and video are not output together
even if a Ø 3.5 mm stereo minijack cable is connected to the
shared AUDIO IN terminal for PC IN and HDMI IN 2.
- Check the "Audio Select" setting. Set "Audio Select" to
"HDMI+Analog".
Page 8-2
Bluetooth (smartphone)
playback cannot be
displayed on the TV.
Check pairing.
Miracast image/audio
cannot be output to the
TV.
Check pairing.

Sharp LC-90LE657U Specifications

General

Display diagonal	90 \
Display brightness	- cd/m²
Native refresh rate	120 Hz
LED backlighting type	Full-Array
Supported video modes	1080p
Contrast ratio (dynamic)	8000000:1
Display diagonal (metric)	228.64 cm
Screen format adjustments	16:9
Supported graphics resolutions	1920 x 1080 (HD 1080)
Motion interpolation technology	AquoMotion 240
3D	Yes
3D glasses quantity	2
Tuner type	Analog & digital
Analog signal format system	NTSC
Digital signal format system	ATSC
RMS rated power	20 W
DVI port	No
Headphone outputs	-
HDMI ports quantity	4
DVI-D ports quantity	0
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Component video (YPbPr/YCbCr) in	1
Wi-Fi standards	802.11a, 802.11b, 802.11g
Smart modes	Game
Lifestyle apps	Skype
Number of OSD languages	3
On Screen Display (OSD) languages	ENG, ESP, FRE
Product color	Black
Panel mounting interface	600 x 400 mm
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	- W
Power consumption (typical)	381 W
Package depth	335 mm
Package width	2237 mm
Package height	1461 mm
Package weight	92500 g

Weight and Dimensions

Depth (with stand)	434 mm
Height (with stand)	1243 mm
Weight (with stand)	68000 g
Depth (without stand)	116 mm
Width (without stand)	2054 mm
Height (without stand)	1211 mm
Weight (without stand)	64000 g