– 8 –
MD-MT866H/MD-MT866W
Error Messages
ERROR MESSAGES
BATT EMPTY
(LoBATT)
BLANK MD
(BLANK)
Can’t COPY
(Can’tC)
Can’t EDIT
(Can’tE)
Can’t READ *
(Can’tS)
(Can’tT)
(Can’tU)
Can’t REC
(Can’tR)
Can’t STAMP
Can’t WRITE
(Can’tW)
CHARGEmode
DEFECT
(DEFECT)
DISC FULL
Er-MD **
(ErMD*)
HOLD
(HOLD)
LOCKED
(Can’tLOCK)
MEANING
● The battery is run down.
● Nothing is recorded.
● You tried to record from a copy prohib-
ited MiniDisc.
● A track cannot be edited.
● The disc data cannot be read because the
disc is damaged.
● Recording cannot be performed correctly
due to vibration or shock.
● Stamp function does not work.
● Cannot save the TOC information correctly
to a MiniDisc. (A large portion of the disc
has been damaged.)
● The Charge/Operation switch is not set to
the operation mode when using this unit
with the AC adaptor.
● The disc is scratched.
● The disc is out of recording space.
● The microprocessor has reported a sys-
tem fault and the unit is out of order.
● The unit is in the hold mode.
● You removed a MiniDisc whilst recording
or editing.
REMEDY
● Charge the rechargeable battery or replace the alkaline battery
(or use the AC adaptor for power).
● Replace the disc with a recorded disc.
● Record using the analogue cable.
● Change the stop position of the track and then edit it.
● Reload the disc.
● Replace it with another recorded disc.
● Re-record or replace it with another recordable disc.
● Check the number of tracks.
● Replace the disc with another recordable disc.
● Set the Charge/Operation switch to the operation mode.
● If the sound you hear is not right, record again.
● Replace the disc with another recordable disc.
● Replace it with another recordable disc.
● To have it repaired, go to the distributor where you purchased the
unit.
● Return the HOLD switch to its original position.
● Turn off the power and remove the MiniDisc.
ERROR MESSAGES
NO DISC
NO SIGNAL
(noSIG.)
PLAY MD
(PLAYmd)
POWER ?
PROTECTED
SORRY
(SORRY)
TEMP OVER
(TEMP!)
TOC FORM **
(Tform**)
TOC FULL
Tr. Protect
? DISC
(? DISC)
MEANING
● A disc has not been loaded.
● Poor connection of the digital cable.
● No output signal comes out from the con-
nected unit to playback.
● The input signal has improper sampling
frequency.
● You recorded on a playback-only disc.
● The battery charger is defective.
●
The write protection tab of a MiniDisc is
set to the protected position.
●
You tried to record on a playback-only disc.
● Since a track number is currently being
located or updated, the unit cannot accept
your command.
● The temperature is too high.
● There is an error in the recording
signal.
● There is no space left for recording char-
acter information (track names, disc
names, etc.).
● The track has been protected from being
erased.
● A disc which contains data other than
music was played.
● There is an error in the signal recorded
on the disc.
● Stamping is not possible.
REMEDY
● Load a disc.
● Connect the digital cable securely.
●
If the portable CD player has a function to prevent sound skips, deacti-
vate it.
● Playback with the connected unit.
●
Replace it with a recordable disc.
● To have it repaired, go to the distributor where you purchased
the unit.
●
Move the write protection tab back to its original position.
● Replace it with a recordable MiniDisc.
● Wait for a while and try the operation again.
● Turn off the power, and wait for a while.
● Erase all of the tracks, and then record again.
● Replace it with another recordable disc.
● Edit the track with the device on which it was recorded.
● A disc which contains non-music data cannot be played.
● Replace it with another recorded disc.
● Retry.
( ) : Error messages seen on the remote control.
Number or symbol appears in * position.
To Next Page
Loading...
Need help?
General
