Sharp MX-C301W

SHARP
TEST SIMULATION
51
55
MFP Data Setting
2
Scanner soft switch setting
3
Controller soft switch setting:-
SW1-5
Auto clear function before copy
job execution:-
0 =Disabled, 1 = Enabled
SW3-6
Process mixed original size
printing for duplex mode:-
0 =Disabled, 1 = Enabled
SW3-7
HP Compatibility Mode:-
0 =Disabled, 1 = Enabled
SW6-1
Ethernet Speed Auto
negotiation:-
0 = Enabled, 1 = Disabled
SW6-2
Ethernet Link Speed:-
0 = 100Base TX, 1 = 10Base T
SW6-3
Ethernet Duplex Mode:-
0 = Full, 1 = Half
SW6-4
Ethernet 100/1000 Link Speed:-
0 = 100Base TX, 1 = 1000Base T
SW9-5
Maintenance notification setting
by Printer MIB:-
0 = Enabled, 1 = Disabled
SW9-6
Duplex Binding control:-
0:Binding OFF (Default)
1:Binding ON
SW18-6
Hide Device Counter Clear
(SIM24-6 to 24-15)
0 = Hide [Default], 1 = Display
SW22-5
Display toner remaining (MFP
Status) [MX-C301W]:-
0= Disabled, 1 = Enabled/Display
SW24-7
Continuous print mode for OSA
(job queuing for external
accounting) [MX-C301W]:-
0 = Job Queue Disabled
1 = Job Queue Enabled
SW25-7
Custom Envelope size (Printer).
0 = Disabled, 1 = Enabled
SW27-8
Retain Scan to Desktop
destination after a scan.
[MX-C301W].
0 = Disabled (Default)
1 = Enabled
SW28-3
Single Email alert notification for
customer.
0 = Disabled (Default)
1 = Enabled
10
Special Stamp setting (Taiwan only)
56
MFP Data Import & Export
1
Transfer data execute (MFP/SD Card/SRAM
& EEPROM) [MX-C301W]
2
Export/Import EEPROM/SD Card/HDD data
3
Document filing backup to USB [MX-C301W]
4
Job log data backup to USB [MX-C301W]
5
Export Adjustment & Settings data to USB
6
Output Jam/Trouble data [MX-C301W]
7
Export Syslog data to USB [MX-C301W]
60
Memory Operation & Test
1
SDRAM read/write test (MFP PWB)
61
LSU Writing Adjustment/Test
1
LSU test (Polygon & BD detection check)
3
LSU power auto setup
4
LSU position adjustment (CMYK)
62
HDD Operation & Test [MX-C301W]
1
HDD/SD Card format
2
HDD partial read/write check
3
HDD read/write check (all areas)
6
Smart (HDD) self diagnostic test
7
Smart (HDD) self diagnostic error log
8
HDD/SD Card format (excluding system &
operation manual area)
10
Job completion list deletion (with job log)
11
Document filing data deletion
12
Enable/disable auto format for HDD trouble
13
HDD format (manual area only)
14
Delete document filing management data
63
CCD Operation & Adjustment
1
Shading correction data display
2
Shading correction execution (force)
3
CCD gamma & colour correction adjust.
5
CCD gamma & colour correction reset
12
B/W Image (RGB) ratio for lamp adjustment
[MX-C250/300]
64
Self Test Print
1
Test print (Colour mode)
2
Test print (B/W mode)
4
Printer self print test
5
Printer self print test (PCL)
6
Printer self pint test (PS)
7
Adjustment pattern print (Sim46-21)
[MX-C301W]