Sharp PN-LC652

56
E
Specifications
n
Product Specifications
Model
PN-LC862 PN-LC752
PN-LC652
LCD component
86" Class [85-9/16 inch
(217.4 cm) diagonal] TFT
LCD
75" Class [74-1/2 inch
(189.3 cm) diagonal] TFT
LCD
65" Class [64-1/2 inch
(163.9 cm) diagonal] TFT
LCD
Max. resolution (pixels)
3840 x 2160
Max. colors
Approx. 1.07 billion colors
Pixel pitch
0.494 mm (H) × 0.494 mm (V) 0.430 mm (H) × 0.430 mm (V) 0.372 mm (H) × 0.372 mm (V)
Brightness (typical) 450 cd/m
2
*
1
Contrast ratio (typical) 1200: 1
Viewing angle
178° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm)
74-5/8 (W) x 41-15/16 (H)
(1895.0 x 1066.0)
64-15/16 (W) x 36-9/16 (H)
(1649.7 x 927.9)
56-1/4 (W) x 31-5/8 (H)
(1428.5 x 803.5)
Computer input signal
Analog RGB (0.7 Vp-p) [75 Ω]
Sync signal
Horizontal/vertical separate (TTL: positive/negative)
Plug and play
VESA DDC2B
Input
terminals
Video Mini D-sub 15 pin, 3 rows x 1
Mini AV in x 1
HDMI x 3
DisplayPort x 1
USB Type-C x 1
Serial (RS-232C)
D-sub 9 pin x 1
Audio
3.5 mm mini stereo jack x 1
Output
terminals
Video HDMI x 1
Audio
3.5 mm mini stereo jack x 1
Digital audio output (optical) x 1
USB port USB 3.0 compliant x 4
LAN terminal 10 BASE-T/100 BASE-TX/1000 BASE-T
System CPU Arm Cortex-A55 processor (Quad-Core)
Memory 4GB
Storage 16GB
Wireless LAN IEEE802.11ac/n/a/g/b compliant
Encryption mode: Enhanced Open, WEP, WPA, WPA2
Bluetooth 4.2 compliant
Supported protocols: A2DP, AVRCP, GATT, HID
Expansion slot 19V, 4.74A (power supplied when expanding the functions with an optional part)
Speaker output 15 W + 15 W
Touch
Panel
Detection method Infrared blocking detection method
Computer connector USB (3.0 compliant) (Type B) x 2
Power requirement AC 100 - 240 V, 5.6 A,
50/60 Hz
AC 100 - 240 V
, 4.7 A,
50/60 Hz
AC 100 - 240 V, 4.4 A,
50/60 Hz
Operating temperature
*
2
*
3
41°F to 95°F (5°C to 35°C)
Operating humidity
*
3
20% to 80% (no condensation)
Power consumption*
4
(Max / networked standby mode
*
5
/ standby mode
*
5
/ off mode)
260 W
(500 W/2 W/0.5 W/0 W)
200 W
(420 W/2 W/0.5 W/0 W)
180 W
(390 W/2 W/0.5 W/0 W)
Dimensions inch (mm)
(excluding protrusions)
Approx. 77-1/2 (W) x 3-7/16
(D) x 46-1/16 (H) (1967.9 x
87.1 x 1170.2)
Approx. 67-13/16 (W) x
3-7/16 (D) x 40-5/8 (H)
(1722.5 × 87.1 × 1032.1)
Approx. 59-1/2 (W) x 3-3/8
(D) x 36-1/8 (H) (1511.6 ×
85.9 × 917.9)
Weight lbs. (kg)
Approx. 143.3 (65) Approx. 112.4 (51) Approx. 84.9 (38.5)
*1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the
equipment, it is not possible to precisely maintain a constant level of brightness. This is the brightness of the LCD panel, not the
brightness of the product.
*2 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments.
*3 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied.
*4 Factory setting. (When no optional part is attached.)
*5 When no optional part is attached.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.