Sharp SX8800H - Service Information; Supply Voltage Setting Procedure

REF.NO.
116
A117
118
119
120
121
123
124
125
126
127
128
129
A\130
A\130
A130
A131
A132
133
601
602
603
604
605
606
607
608
609
610
611
612
613
614
PART NO. * DESCRIPTION
LANGT1861AFFW J Bracket,Main PWB
LBSHC0004AGZZ J Bushing,AC Power Supply
Cord
LCHSM0814AF FW Chassis
LHLDW1124AFZZ Nylon Band,80mm
LHLDW9061AFZZ Wire Holder
LHLDZ1441AF09 Holder,LED
MLEVP0942AFZZ Lever,Knob
PCOVU7151AFZZ Cover,Lamp
PRDAR0570AFFW Heat Sink
PRDAR0583AFFW Heat Sink
PRDAR0684AF FW Heat Sink
PRDAR0685AFFW Heat Sink Plate
PSP0-0126AFZZ Sponge
QACCE0103AF08 AC Power Supply Cord
QACCS0051AF00 AC Power Supply Cord
QACCZ0101AF08 AC Power Supply Cord
QFSHD2104AFZZ Fuse Holder
QLUGP0165AFZZ Lug
QHWS-0001CEFN Lug
LX-HZ0087AFFD
LX-HZ0169AFFD
LX-JZ0123AFFD
Screw, ¢3 X 8mm
Screw, 64 X 8mm
Screw, 3 X 8mm
ecreeeeee ee OOO eee OOO
XHBSD30P06000 Screw, ¢3 X 6mm
XHBSD30P08000 Screw, 63 X 8mm
XHBSF30P06000 Screw, ¢3 X 6mm
XHBSF30P08000 Screw, 63 X 8mm
XHSSF30P08000 Screw, ¢3 X 8mm
XJBSD30P08000 Screw, 3 X 8mm
XJBSD30P12000 Screw, ¢3 X 12mm
XJBSD30P16000 Screw, ¢3 X 16mm
XJBSF30P08000 Screw, 63 X 8mm
XJBSF30P12000 Screw, 3 X 12mm
XJBSD30P10000 Screw, ¢3 X 10mm
ACCESSORIES/PACKING PARTS
SPAKA2200AFZZ J Packing Add.,Left
SPAKA2201AFZZ J Packing Add.,Right
SPAKC5372AFZZ J Packing Case
SPAKP0985AFZZ J Polyethylene Bag,Unit
P.W.B. ASSEMBLY (Not Replacement Item)
PWB-A1~3
PWB-B1~4
DCEKM0368AF03 J Main/Power/Trans.
(Combined Ass’y)
DCEKN0053AF03 J Display Meter/Lamp 1/
Lamp 2/Headphones
(Combined Ass’y)
CODE
AE
AB
BA
AC
AG
AC
AD
AL
AW
BE
AS
AS
AN
AM
AR
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AP
AP
AX
AK
SX-8800H SX-8800H
©
SERVICE INFORMATION
Supply Voltage Setting
The SX-8800H can operate on either
115V or 230V power supply, and it has
been adjusted to the 230V position before
leaving the factory. When operating
the unit on 115V power supply, take the
following procedures.
1. Remove the cabinet according to the
"DISASSEMBLY’ instruction.
2. Cut out the jumper wire JW1A,B and add
the jumper wire JW2A,B to the position
shown in PWB-A2/A3.
3. Replace the fuse F891/F892 with a fuse
of T4 A. (QFS-B402CAFNi), (AF).
©
SERVICE-INFORMATION
Einstellung der Versorgungsspannung
Das SX-8800H kann Uber eine Netz-
spannung von 115V oder 230V betrieben
werden, und vor dem Versand ist das auf
der 230V-Stellung eingestellt. Beim Betrieb
des Geradts Uber eine Netzspannung von
115V die folgenden Verfahren ausfiihren.
1.Das Gehause gema& der Anleitung
"ZERLEGEN” entfernen.
2.Den Schaltdraht JW1A,B abschneiden
und den Schaltdraht JW2A,B zu
der in PWBA2/A3 gezeigten Stelle
hinzufiigen.
3.Die Sicherung F891/F892 gegen
eine von T4 A (QFS-B402CAFNi), (AF)
auswechseln.
Lesi L982
AC POWER SUPPLY CORD
(130)
AC 230V
SOHz
PIO 8-C PS 3-c
Figure 18
©
INFORMATION DE
SERVICE
Réglage de la tension
Le SX-8800H fonctionnant sur le
secteur soit de 115V soit de 230V, a
été préréglé sur le 230V a la sortie de
l‘usine. Pour le faire fonctionner sur le
secteur de 115V, suivre les procédés
ci-dessous.
1. Déposer le coffret conformément a
‘instruction 7DEMONTAGE’.
2. Couper le fil volant JW1A,B et ajouter
le fil volant JW2A,B a_ l’endroit
indiqué sur la PWB-A2/A3.
3. Changer le fusible F891/F892 pour
celui de T4 A. (QFS-B402CAFNi), (AF).
P
pues TRANSFOR!
[ A9008-5245NS - IS - K
Printed in Japan
In Japan gedruckt
Writer
and
Eaitor:
Quality
&
Reliability
Control
Center
of
Audio
Systems
Group,
Sharp
Corp.
Imprimé
au
Japon
SG