Sharp UP-810F - Locking after Daily Net Resetting; Open Store;Close Store at Stand Alone POS with Online; Polling Cycle; Reverse ONLINE Channel in Closed Store

UP-810F/820N/820F(U) SRV MODE PROGRAMMING (“SETTING”)
3 – 14
923-D: 1. Polling cycle (second)
Ex:
When input D = 5, the master waits 5 sec., and then the master starts T-
LOG POLLING to next machine.
[JOB#924] : MRS=1433
924-A, B, C: Not used (Fixed at “143”)
924-D: 1. Locking after daily net resetting
2. Locking after transaction resetting
* Setting of lock timing for REG-mode entries after individual periodic
total resetting.
[JOB#925] : MRS=0303
925-A:Not used (Fixed at “0”)
925-B: 1. Various individual resetting.
* Individual resetting Enable/Disable: The master alone can be made
capable of resetting by selecting “Disable”
925-C: 1. Report printing when consolidation daily and periodic total
transaction reading or resetting is taken
* Type of printing of daily total and periodic total transaction X/Z
reports: The following of three types are available:
a) Printing of only X/Z reports on individual machines
b) Printing of a consolidation X/Y report only
c) Printing of X/Z reports on individual machines, followed by the
printing of a consolidation X/Y report.
925-D: 1. Resetting is allowed when the server is remained sign on
2. Resetting in the open store state
[JOB#926] : MRS=0000
925-D: 1. Printing “LAST VOID DATA” on KP
2. Printing “PAST VOID DATA” on KP
926-B: 1. Sending “REFUND DATA” on KP.
926-C: 1. Open store/Close store at stand alone POS with online
2. Send AT command string with “Open Store” job
3. Send AT command string with “Close Store” job
926-D: 1. Reverse ONLINE channel in closed store
1. Polling cycle (second) 923-D Flat Normal
0 ~ 9 Sec. 0-9 0 0
1. Locking after
daily net reset-
ting
2. Locking after
transaction
resetting
924-D Flat Normal
Ye s
Yes 0
No 1
No
Yes 2
No 3 ★★
1. Various individual resetting 925-B Flat Normal
Disable 0
Enable 3 ★★
1. Report printing when consolidation
daily and periodic total transaction
reading or resetting is taken
925-C Flat Normal
Printing of both i.e. reports on individual
machines and consolidation report on the
entire system
0 ★★
Printing of consolidation report on the
entire system
1
Printing of report on individual register 2
1. Resetting is
allowed when
the server is
remained sign
on
2. Resetting in the
open store state
925-C Flat Normal
No
Disable 0
Enable 1
Ye s
Disable 2
Enable 3 ★★
1. Printing “LAST
VOID DATA” on
KP
2. Printing “PAST
VOID DATA” on
KP
926-A Flat Normal
Both last-void-data
and voided item
aren’t printed
Both last-void-data
and voided item
aren’t printed
0 ★★
Both are printed 1
Both are printed
Both last-void-data
and voided item
aren’t printed
2
Both are printed 3
1. Sending “REFUND DATA” on KP 926-B Flat Normal
Ye s 0 ★★
No 2
1. Open
store/
Close
store at
stand
alone
POS with
online
2. Send AT
com-
mand
string
with
“Open
Store” job
3. Send AT
com-
mand
string
with
“Close
Store” job
926-C Flat Normal
No
No
No 0 ★★
Yes 1
Ye s
No 2
Yes 3
Yes
No
No 4
Yes 5
Ye s
No 6
Yes 7
1. Reverse ONLINE channel in closed
store
926-C
Flat Normal
No 0 ★★
Ye s 4