To Next PageTo Next PageWhat to do if my Sherwood Receiver has no power?
If your Sherwood Receiver isn't powering on, first, ensure the AC input cord is securely connected. If it is, check the AC wall outlet by plugging in a lamp or another appliance to see if the outlet is working.
Why is there no sound coming from my Sherwood Newcastle R-925?
If you're not getting any sound from your Sherwood Receiver, there are several things to check: * Make sure the speaker cords are properly connected. * Adjust the master volume to an audible level. * Ensure the MUTE button is not activated. * Verify that the speakers are switched on. * Confirm that the correct digital input is selected. * Select the correct input source. * Check all connections between the components to ensure they are correct.
How to fix a Sherwood Newcastle R-925 Receiver remote control that's not working?
If your Sherwood Receiver's remote control isn't working, start by replacing the batteries. If that doesn't solve the issue, make sure there's nothing blocking the remote sensor on the receiver.
Why can't my Sherwood Newcastle R-925 Receiver pick up any stations?
If your Sherwood Receiver isn't receiving any stations, make sure an antenna is connected. Then, tune in the desired station frequency. If the issue persists, try repositioning the antenna.
What to do if there's no sound from the rear speakers on my Sherwood Newcastle R-925?
If you're not hearing sound from the rear speakers of your Sherwood Receiver, ensure that a surround mode is selected. Also, check that the master volume and rear level are appropriately adjusted. If you are using a monaural source, select a stereo or surround source. Finally, make sure that Dolby 3 Stereo mode is not selected; instead, choose the desired surround mode.
How to improve poor FM reception on my Sherwood Newcastle R-925 Receiver?
To improve FM reception on your Sherwood Receiver, first, ensure that an antenna is connected. If one is already connected, try changing its position to find the best reception.
Why is there no sound coming from the center speaker on my Sherwood Receiver?
If you're not getting any sound from the center speaker on your Sherwood Receiver, make sure you've selected Dolby DIGITAL (AC-3), Dolby Pro Logic, or Dolby 3 Stereo mode. Also, check that the master volume and center level are not set too low.
What to do if my Sherwood Receiver cannot receive preset stations?
If your Sherwood Receiver can't receive preset stations, it could be due to an incorrect station frequency being memorized. In this case, memorize the correct station frequency. Alternatively, the memorized stations might have been cleared, so try memorizing the stations again.
How to stop hissing noise during FM reception on my Sherwood Newcastle R-925 Receiver?
If you're experiencing continuous hissing noise during FM reception on your Sherwood Receiver, especially with stereo broadcasts, the signals may be weak. Try changing the position of the antenna. If the problem persists, consider installing an outdoor antenna.
What causes hissing noise during AM reception on my Sherwood Receiver?
If you're hearing continuous or intermittent hissing noise during AM reception on your Sherwood Receiver, especially at night, it's likely due to interference from motors, fluorescent lamps, lightning, or other noise sources. Try to keep the receiver away from these sources. If that doesn't help, consider installing an outdoor AM antenna.
General| Type | AV Receiver |
|---|---|
| Channels | 5.1 |
| Total Harmonic Distortion | 0.08% |
| Signal-to-Noise Ratio | 100 dB |
| Digital Inputs | Coaxial, Optical |
| Headphone Output | Yes |
| Video Connections | Composite, S-Video |
| Power Output | 100 W per channel (8 ohms) |
| Frequency Response | 20 Hz - 20 kHz |
| Input Sensitivity | 200 mV (Line) |
| Tuner Section | FM, AM |
| Analog Outputs | 1 |
Details on how to unpack and install the receiver, including safety and placement advice.
Details on compliance with FCC rules regarding digital devices and radio frequency energy.
Information for users in USA, Canada, and other countries regarding voltage and plug safety.
Instructions on how to set the AC voltage selector switch on the rear panel.
Guide on connecting FM and AM antennas, including types and placement.
Guide on connecting audio components such as turntables, CD players, and tape decks.
Instructions for connecting video sources like LD players and DVD players to the receiver.
Instructions for connecting a multi-room adaptor to the receiver.
Details on connecting digital audio sources like LD players and components with digital outputs.
How to connect Sherwood components using the DIGI LINK system for control.
Guidance on connecting front, rear, and center speakers, including polarity and impedance.
Connecting a pre-amplifier to the receiver's main inputs for front channels.
Connecting pre-amplifiers or powered speakers to the receiver's pre-out jacks for higher volume.
Explanation of the information displayed on the fluorescent screen.
Details on the AUX/VIDEO input jacks and their connection possibilities.
Information on the effective range and angles for operating the remote control.
Instructions on how to insert batteries into the remote control unit.
Step-by-step guide on how to turn on the receiver and select an input source for listening.
Explanation of how to use the TAPE 2 MONITOR jacks for recording or listening to tape decks.
Details on selecting digital or analog inputs and understanding input indicators.
Adjusting overall volume, bass, and treble for preferred sound.
Fine-tuning stereo balance and subwoofer output.
Engaging features like Cinema Bass and muting the sound.
Details the 7 different surround sound modes available (Dolby Digital, Pro Logic, etc.).
Explains the concept of delay time in surround sound and its adjustment.
Guide on optimal placement of front, center, rear, and subwoofer speakers for best surround effect.
Instructions on how to select and enjoy different surround sound modes.
Procedures for adjusting center speaker and subwoofer settings.
How to check the current settings for center speaker and subwoofer.
Adjusting speaker volume levels using test tones in Dolby modes.
Adjusting rear speaker volume relative to front speakers in other modes.
How to manually tune radio frequencies.
How to directly enter radio frequencies using the remote or front panel.
How to automatically scan and tune to radio stations.
How to select a previously stored radio station.
How to scan through stored radio stations.
How to switch between stereo and mono modes for FM reception.
Steps to select an input source and record onto TAPE 1.
Steps to select an input source and record onto TAPE 2 MONITOR.
How to dub video sources like LD players to VCR 1.
How to listen to other audio sources (e.g., CD) while dubbing to VCR 1.
How to enjoy other video sources (e.g., DVD) while dubbing to VCR 1.
Dubbing LD video and CD audio signals to VCR 1 simultaneously.
How to use the dynamic range compression feature for movies.
Setting the sleep timer to automatically turn off the receiver.
Adjusting the brightness of the front panel displays.
How to assign custom labels to video input sources.
How to edit or delete existing video labels.
Verifying connected video components and their content.
Technical specifications for the audio amplification circuitry.
Technical specifications for audio processing and radio tuners.
General specifications including power, dimensions, and weight.
