To Next PageTo Next PageWhat to do if other components don't respond to my Sherwood Newcastle R-925 Receiver's remote?
If other system components aren't responding to your Sherwood Receiver's remote control, the DIGI LINK connections may not be properly made. Ensure that you make proper DIGI LINK connections.
General| Type | AV Receiver |
|---|---|
| Channels | 5.1 |
| Total Harmonic Distortion | 0.08% |
| Signal-to-Noise Ratio | 100 dB |
| Digital Inputs | Coaxial, Optical |
| Headphone Output | Yes |
| Video Connections | Composite, S-Video |
| Power Output | 100 W per channel (8 ohms) |
| Frequency Response | 20 Hz - 20 kHz |
| Input Sensitivity | 200 mV (Line) |
| Tuner Section | FM, AM |
| Analog Outputs | 1 |
Details on how to unpack and install the receiver, including safety and placement advice.
Details on compliance with FCC rules regarding digital devices and radio frequency energy.
Information for users in USA, Canada, and other countries regarding voltage and plug safety.
Instructions on how to set the AC voltage selector switch on the rear panel.
Guide on connecting FM and AM antennas, including types and placement.
Guide on connecting audio components such as turntables, CD players, and tape decks.
Instructions for connecting video sources like LD players and DVD players to the receiver.
Instructions for connecting a multi-room adaptor to the receiver.
Details on connecting digital audio sources like LD players and components with digital outputs.
How to connect Sherwood components using the DIGI LINK system for control.
Guidance on connecting front, rear, and center speakers, including polarity and impedance.
Connecting a pre-amplifier to the receiver's main inputs for front channels.
Connecting pre-amplifiers or powered speakers to the receiver's pre-out jacks for higher volume.
Explanation of the information displayed on the fluorescent screen.
Details on the AUX/VIDEO input jacks and their connection possibilities.
Information on the effective range and angles for operating the remote control.
Instructions on how to insert batteries into the remote control unit.
Step-by-step guide on how to turn on the receiver and select an input source for listening.
Explanation of how to use the TAPE 2 MONITOR jacks for recording or listening to tape decks.
Details on selecting digital or analog inputs and understanding input indicators.
Adjusting overall volume, bass, and treble for preferred sound.
Fine-tuning stereo balance and subwoofer output.
Engaging features like Cinema Bass and muting the sound.
Details the 7 different surround sound modes available (Dolby Digital, Pro Logic, etc.).
Explains the concept of delay time in surround sound and its adjustment.
Guide on optimal placement of front, center, rear, and subwoofer speakers for best surround effect.
Instructions on how to select and enjoy different surround sound modes.
Procedures for adjusting center speaker and subwoofer settings.
How to check the current settings for center speaker and subwoofer.
Adjusting speaker volume levels using test tones in Dolby modes.
Adjusting rear speaker volume relative to front speakers in other modes.
How to manually tune radio frequencies.
How to directly enter radio frequencies using the remote or front panel.
How to automatically scan and tune to radio stations.
How to select a previously stored radio station.
How to scan through stored radio stations.
How to switch between stereo and mono modes for FM reception.
Steps to select an input source and record onto TAPE 1.
Steps to select an input source and record onto TAPE 2 MONITOR.
How to dub video sources like LD players to VCR 1.
How to listen to other audio sources (e.g., CD) while dubbing to VCR 1.
How to enjoy other video sources (e.g., DVD) while dubbing to VCR 1.
Dubbing LD video and CD audio signals to VCR 1 simultaneously.
How to use the dynamic range compression feature for movies.
Setting the sleep timer to automatically turn off the receiver.
Adjusting the brightness of the front panel displays.
How to assign custom labels to video input sources.
How to edit or delete existing video labels.
Verifying connected video components and their content.
Technical specifications for the audio amplification circuitry.
Technical specifications for audio processing and radio tuners.
General specifications including power, dimensions, and weight.
