To Next PageTo Next PageWhat to do if my Sherwood Newcastle R-956 Receiver has no power?
If your Sherwood Receiver isn't powering on, first, ensure the AC input cord is securely connected. Then, check the AC wall outlet by testing it with a lamp or another appliance. You can also try switching the unit off and on again. If the problem persists, consult your dealer.
Why is there no sound coming from my Sherwood Receiver?
If there's no sound from your Sherwood Receiver, check the speaker connections and ensure they are secure. Make sure the master volume isn't set too low and that the MUTE button is not activated. Also, verify that you've selected the correct digital input and input source. Finally, ensure all connections between components are correctly made.
Why is the remote control for my Sherwood Receiver not working?
If the remote control for your Sherwood Receiver isn't working, the batteries may be exhausted or not loaded correctly. Try replacing the batteries. Also, make sure nothing is obstructing the remote sensor on the receiver.
What to do if my Sherwood Receiver is not receiving any stations?
If your Sherwood Receiver isn't receiving any stations, ensure an antenna is connected. Also, make sure you've tuned in the desired station frequency and try repositioning the antenna for better reception.
Why is there no sound from the rear speakers on my Sherwood Receiver?
If you're not getting sound from the rear speakers on your Sherwood Receiver, it could be due to several reasons: * The surround mode might be switched off (set to normal stereo mode). * The master volume and rear level might be too low. * You might be using a monaural source. * The rear speaker setting might be set to “N”. To resolve this, try selecting a surround mode, adjusting the master volume and rear level, selecting a stereo or surround source, and choosing the desired rear speaker setting.
Why is there no sound from the center speaker on my Sherwood Newcastle R-956?
If there's no sound from the front center speaker of your Sherwood Receiver, check if TruSurround or normal stereo mode is selected. Also, ensure the front center speaker setting isn't set to “N”. Finally, make sure the master volume and center level are appropriately adjusted.
How to fix poor FM reception on Sherwood Newcastle R-956 Receiver?
To improve poor FM reception on your Sherwood Receiver, ensure an antenna is connected. You should also try changing the position of the antenna to find the best reception.
Why can't I receive preset stations on my Sherwood Newcastle R-956?
If you cannot receive preset stations on your Sherwood Receiver, it might be because an incorrect station frequency was memorized, or the memorized stations were cleared. Try memorizing the correct station frequency or memorizing the stations again.
How to stop hissing noise during FM reception on my Sherwood Receiver?
If you're experiencing a continuous hissing noise during FM reception on your Sherwood Receiver, especially when receiving a stereo broadcast, it could be due to weak signals. Try changing the position of the antenna or installing an outdoor FM antenna.
How to stop hissing noise during AM reception on my Sherwood Newcastle R-956?
If you're experiencing continuous or intermittent hissing noise during AM reception on your Sherwood Receiver, especially at night, it's likely caused by interference from motors, fluorescent lamps, or lightning. Try keeping the receiver away from these noise sources or installing an outdoor AM antenna.
Guide to unpacking the audio/video receiver and initial setup.
Important safety and operating guidelines to read before use.
Instructions for connecting FM and AM antennas.
Guide for connecting turntables, CD players, and tape decks.
Explains the information shown on the receiver's front display.
Details about the front panel video input jacks.
Explains the basic functions of the Sherwood and OSD modes for the remote.
Step-by-step guide to selecting input sources and listening to audio.
How to configure speaker settings for different channels and subwoofer.
Guide to adjusting the volume level for individual speaker channels.
Steps for automatically tuning in radio stations by band and frequency.
Process for manually tuning radio stations using the control knob.
Information on what settings are memorized and how they are backed up.
Steps for recording audio using the TAPE MONITOR function.
Process for dubbing video signals from one source to VIDEO 1.
How to check current operational settings like input, surround, and tone.
Explains dynamic range compression for Dolby Digital sound tracks.
Guide to setting the automatic shut-off timer for the receiver.
How to adjust the brightness of the receiver's display panels.
How the receiver shows current operational status on the monitor TV.
Guide to navigating setup menus for various receiver functions.
General