Shimax MAC5D User Manual

10
1010
10
8
88
8-
--
-4.AT (Auto Tuning)
4.AT (Auto Tuning)4.AT (Auto Tuning)
4.AT (Auto Tuning)
・If AT is performed by FIX (constant value control)、AT monitor LED blinks and light is put out by termination or intermediate release.
・AT at the time of 2 output specification is as follows.
At the time of heating / cooling operation and cooling / heating operation = OUT1, OUT2 common - PID value At the time of heating / heating operation
and cooling / cooling operation, only OUT1 performs AT. OUT 2 output while performing AT is 0% or output limiter lower limit v
8
88
8-
--
-5 .Output
5 .Output5 .Output
5 .Output-
--
-characteristics figure
characteristics figurecharacteristics figure
characteristics figure
2-output -characteristics is shown in the following figure.
◎ Conditions: P operation, manual reset ( )  －50.0%
1) OUT 1 RA (heating)
1) OUT 1 RA (heating) 1) OUT 1 RA (heating)
1) OUT 1 RA (heating) ・
・・
・OUT 2 DA (cooling) operation
OUT 2 DA (cooling) operationOUT 2 DA (cooling) operation
OUT 2 DA (cooling) operation 2) OUT 1RA (heating)
2) OUT 1RA (heating)2) OUT 1RA (heating)
2) OUT 1RA (heating)・
・ ・
・ OUT 2 RA (heating)
OUT 2 RA (heating)OUT 2 RA (heating)
OUT 2 RA (heating)
9. Trouble
9. Trouble 9. Trouble
9. Trouble
9
99
9-
--
-1. Cause and Treatment of Main Defects
1. Cause and Treatment of Main Defects 1. Cause and Treatment of Main Defects
1. Cause and Treatment of Main Defects
  
 



 









 



9
99
9-
--
-2. Cause and Treatment of Error Display
2. Cause and Treatment of Error Display2. Cause and Treatment of Error Display
2. Cause and Treatment of Error Display
Abnormality Display of Measurement Input
Abnormality Display of Measurement InputAbnormality Display of Measurement Input
Abnormality Display of Measurement Input
Errorｄisplay Contents Cause Treatment

（ＨＨＨＨ）
Scale over in upper limit 1.wire breaking of thermocouple input
2.wire breaking of resistance bulb input A
3.when input exceeds upper limit of measuring range by 10%
1.wire breaking check of thermocouple input wiring, replacement of thermocouple
2.check of resistance bulb A wiring, replacement of resistance bulb
3.check of input voltage value and current value, input transmitter and specification
(matching of incoming signal and meter specification)

（ＬＬＬＬ）
Scale over in lower limit 1.when input exceeds lower limit of measuring range by 10%
2.wire breaking of resistance bulb input B*
1.polarity of input is everse, check of wiring and an input transmitter
2.check of resistance bulb B wiring, replacement of resistance bulb
*B: Wiring of MAC5A, 5B's terminal No.11,Wirring of MAC5C ‘s terminal No,8
Wiring of MAC 5D's terminal No.5

（Ｂ－－－）
Breaking of resistance bulb input 1.wire breaking of b* 1.check of resistance bulb wiring
*b: Wiring of MAC 5A, 5B's terminal No.12,Wirring of MAC5C ‘s terminal No,9
wiring of MAC 5D's terminal No.6
2.multiple wire breaking combinations in Abb
(A and B, A and b, B and b, all of ABB)
2.replacement of resistance bulb

（ＣＪＨＨ）
Cold junction (CJ) temperature of thermocouple
input is scale over in upper limit side
When ambient temperature of a meter exceeds 80℃ 1.make Ambient temperature of meter within use environment condition temperature
2. Check the meter when ambient temperature is not over 80℃

（ＣＪＬＬ）
Cold junction (CJ) temperature of thermocouple
input is scale over in lower limit side
When ambient temperature of meter becomes less
than －20℃
1.make Ambient temperature of meter within use environment condition temperature
2. Check the meter when ambient temperature is not less than -20℃
Output 100％
Control output1（RA Characteristics）
Control output2（DA Characteristics）
▲
-DB
△
DB＝0
▲
+DB
▲
-DB
△
DB＝0
▲
+DB
△：Setting Value（SV） ▲：DB（Dead Band）
Control output1（RA Characteristics） Control output2（DA Characteristics）
Output 0％
Output 100％
Output 100％
Output 0％
△：Setting Value（SV） ▲：DB（Dead Band）
10. Specification
10. Specification10. Specification
10. Specification

   


  

  








   





Shimax MAC5D Specifications

General

Brand	Shimax
Model	MAC5D
Category	Controller
Language	English