9
99
9
thermo couple
thermo couplethermo couple
thermo couple
B,R,S,K,E,J,T,N:JIS/IEC
B,R,S,K,E,J,T,N:JIS/IECB,R,S,K,E,J,T,N:JIS/IEC
B,R,S,K,E,J,T,N:JIS/IEC
resistance bulb
resistance bulbresistance bulb
resistance bulb
Pt100:JIS/IEC
Pt100:JIS/IECPt100:JIS/IEC
Pt100:JIS/IEC
JPt100: former JIS
JPt100: former JISJPt100: former JIS
JPt100: former JIS
*1
*1*1
*1
thermo couple
thermo couplethermo couple
thermo couple
Accuracy is not guaranteed below B:400℃ (752
Accuracy is not guaranteed below B:400℃ (752Accuracy is not guaranteed below B:400℃ (752
Accuracy is not guaranteed below B:400℃ (752 )
))
).
..
.
*2
*2*2
*2
thermo couple
thermo couplethermo couple
thermo couple
In K, T, U,accuracy is±0.5
In K, T, U,accuracy is±0.5In K, T, U,accuracy is±0.5
In K, T, U,accuracy is±0.5％
％％
％FS for 0
FS for 0FS for 0
FS for 0～－
～－～－
～－100℃ (
100℃ (100℃ (
100℃ (-
--
-148
148148
148 )
))
)
a
aa
an
nn
nd
dd
d
±
±±
±1.0%FS if it is below
1.0%FS if it is below1.0%FS if it is below
1.0%FS if it is below－
－－
－100℃
100℃ 100℃
100℃
*3
*3*3
*3
thermo couple
thermo couplethermo couple
thermo couple
Wre 5
Wre 5Wre 5
Wre 5-
--
-26: Product of Hoskins Mfg. co.,
26: Product of Hoskins Mfg. co.,26: Product of Hoskins Mfg. co.,
26: Product of Hoskins Mfg. co.,
*4
*4*4
*4
thermo couple
thermo couplethermo couple
thermo couple
ＰＬⅡ：
ＰＬⅡ：ＰＬⅡ：
ＰＬⅡ： Platinel
Platinel Platinel
Platinel
*5
*5*5
*5
thermo couple
thermo couplethermo couple
thermo couple
U:DIN43710
U:DIN43710U:DIN43710
U:DIN43710
* Setup of factory shipment is Multi input: thermo couple
* Setup of factory shipment is Multi input: thermo couple * Setup of factory shipment is Multi input: thermo couple
* Setup of factory shipment is Multi input: thermo couple
0
00
0
-
--
-1200℃
1200℃ 1200℃
1200℃
7
77
7-
--
-7 .Measuring range code table
7 .Measuring range code table7 .Measuring range code table
7 .Measuring range code table
With closed DI terminal Execution SV = 2nd SV
With closed DI terminal Execution SV = 3rd SV
With closed DI terminal Execution SV = 4th SV
RUN with closed DI terminal, STBY with open one.
Manual with closed DI terminal,auto with open one.
AT-start with rise edge.
All latching are released by rise edg.
Super key lock with closed DI terminal.
Release with opened.
30m
30m30m
30m
7
77
7-
--
-5 .MODE6:DI setting
5 .MODE6:DI setting5 .MODE6:DI setting
5 .MODE6:DI setting
MODE 6 Digital input setting
MODE 6 Digital input settingMODE 6 Digital input setting
MODE 6 Digital input setting
DI
DI DI
DI ４
４４
４
mode setting screen
mode setting screenmode setting screen
mode setting screen
7
77
7-
--
-6 .DI operation character table
6 .DI operation character table6 .DI operation character table
6 .DI operation character table
8. Supplementary Explanation of Function
8. Supplementary Explanation of Function8. Supplementary Explanation of Function
8. Supplementary Explanation of Function
This is the function to increase the control output gradually with set-up time
at the time of power-on, STBY→RUN, and normal return from scale over.
This is effective for controlling the excessive current to loads, such as a
heater.
1) Soft- start functions in the following conditions.
・At the time of the power-on in automatic operation,
STBY(RST)→RUN, and normal return from scale over.
・Setup of proportional band (P) is other than OFF
・Soft starting time is not OFF
8
88
8-
--
-1 .Auto return function
1 .Auto return function1 .Auto return function
1 .Auto return function
When there is no key operation 3 minutes or more, on the screen except
for basic screen and each monitoring screen, screen automatically shifts to
basic screen. (Auto return).
8
88
8-
--
-2.Output Soft Start Function
2.Output Soft Start Function2.Output Soft Start Function
2.Output Soft Start Function
8
88
8-
--
-3.Event Selection Alarm Operation Figure
3.Event Selection Alarm Operation Figure3.Event Selection Alarm Operation Figure
3.Event Selection Alarm Operation Figure
The figure of alarm operation figure allotted to event 1～3 is shown.
M
MM
M
U
UU
U
-199.9～200.0 -300～400
L
LL
L
T
TT
T
I
II
I
I
II
I
N
NN
N
P
PP
P
U
UU
U
T
TT
T
▲
ON operation
▲
ON operation
：Lower limit absolute value alarm ：Upper limit absolute value alarm
：Upper limit deviation alarm
：Lower limit deviation alarm
▲ ▲
：Without deviation alarm ：With deviation alarm
-10％ 0％ 100％ 110％ PV
：Scale over
ON operation ON operation
ON operation
To Next Page
Loading...
Need help?
General
