EasyManua.ls Logo

Shindaiwa C262 - User Manual

Shindaiwa C262
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
X7502341302
© 02/21 ECHO Incorporated
Operator’s
Manual
C262
GRASS TRIMMER
/ BRUSH CUTTER
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth defects,
or other reproductive harm.
Read and understand all provided literature before use.
Failure to do so could result in serious injury.
Note: This product complies with CAN ICES-2/NMB-2.

Table of Contents

Questions and Answers

  • N
    nathanspencerAug 9, 2025
    Why is my Shindaiwa Trimmer engine hard to start?
    • S
      Stefanie WillisAug 9, 2025
      If your Shindaiwa Trimmer engine isn't starting, several factors could be at play. The fuel strainer or fuel line might be obstructed, in which case you should clean or replace it. A too rich fuel mixture can also be the reason. To solve this, open the choke, clean or replace the air filter, and adjust the carburetor. If there's no spark, ensure the switch is turned ON. Also, check the spark plug; if the gap is incorrect, adjust it to 0.65mm (0.026 in.). If it's covered with carbon or fouled with fuel, clean or replace the plug.
  • K
    Kristopher LivingstonAug 20, 2025
    Why Shindaiwa Trimmer engine does not accelerate properly?
    • J
      Jeffery JohnsonAug 20, 2025
      If your Shindaiwa Trimmer engine runs, but dies or does not accelerate properly, it could be due to normal wear. Clean or replace the worn parts, or clean and adjust them. Improper adjustment could also be the cause, so adjust the trimmer accordingly. In case of normal wear you may need to replace some parts.
  • K
    Kimberly FoxAug 29, 2025
    What to do if Shindaiwa Trimmer engine runs, but dies?
    • J
      Jeffrey AndersonAug 29, 2025
      If your Shindaiwa Trimmer engine runs but dies or doesn't accelerate properly, it could be due to several reasons. Contaminants or residue in the fuel may be the cause, so replace the fuel filter or the fuel itself. Contaminated fuel can also cause this issue, so clean or replace the fuel. A dirty or plugged cooling system can also lead to these symptoms, so clean the cooling system.

Summary

Safety

Manual Safety Symbols and Important Information

Explains safety alert symbols like DANGER, WARNING, CAUTION, and NOTICE.

International Symbols

Personal Condition and Safety Equipment

Guidelines on operator's physical state and necessary protective gear.

Personal Protective Gear

Advice on physical fitness and required safety gear like eye, hand, hearing, and breathing protection.

Electrical and Ventilation Hazards

Warnings about electrical conductors and operating in inadequately ventilated areas.

Equipment Safety

Safety guidelines for using approved attachments and keeping hands away from moving parts.

Assembly

U-Handle Installation

Blade Installation

Instructions for securely installing metal blades on the unit.

Shield Installation (blade operation)

Shield Installation (Nylon line head operation)

Nylon Line Head Installation

Operation

Balance and Adjust Unit

Operation With Blades

Configuration requirements and safety for operating with various types of blades.

Blade Selection

Guidance on choosing the correct blade for different cutting tasks.

Fuel Requirements

Specifications for approved gasoline and two-stroke oil.

Handling Fuel

Safety precautions for mixing, storing, and refueling.

Mixing Instructions

Step-by-step guide for mixing gasoline and oil at a 50:1 ratio.

Starting Cold Engine

Detailed procedure for starting the engine when cold.

Starting Warm Engine

Procedure for starting the engine when it is already warm.

Stopping Engine

Reaction Forces

Maintenance

Maintenance Intervals

Air Filter

Fuel Filter

Spark Plug

Carburetor Adjustment

Nylon Line Replacement

Sharpening Metal Blades

Troubleshooting

Engine Starts Hard or Does Not Start

Troubleshooting chart for engine starting problems.

Engine Runs, But Dies or Does Not Accelerate Properly

Troubleshooting chart for issues with engine running and acceleration.

Storage

Long Term Storage (Over 30 Days)

Specifications

Model and General Specifications

Performance Specifications

Shindaiwa C262 Specifications

General IconGeneral
Engine Type2-Stroke
Displacement25.4 cc
Shaft TypeStraight
Starter SystemRecoil
Cutting Width430 mm

Related product manuals