Why is the audio output so low on my Shure Recording Equipment receiver?
If you're experiencing low audio output at the receiver of your Shure Recording Equipment, check the headphone connection and volume level. If you're only sending a single channel into the P3T transmitter, ensure the MixMode knob isn't turned towards a silent channel; if using one channel, set the P3T transmitter to mono mode.
Why does turning the MixMode knob not affect the sound on my Shure Recording Equipment?
If adjusting the MixMode knob doesn't change the sound on your Shure Recording Equipment, the Stereo-MX/Mono switch on the P3T's rear panel might be set to mono. For MixMode to function, the transmitter must be in Stereo-MX mode. Also, verify that the signals from the mixer to the transmitter are not identical. Finally, check that the bodypack is set to MixMode.
What to do if audio or RF drops out on Shure Recording Equipment?
If you are experiencing audio or RF drops out with your Shure Recording Equipment, perform a scan to ensure the receiver is on a clear, available frequency. Ensure a line-of-sight path between the transmitter antenna and the bodypack receivers. Verify that other wireless devices being monitored, like wireless microphones, aren't experiencing RF dropouts. If using an antenna other than the included one, confirm it's designed for the correct frequency range.
What to do if there is no sound from my Shure Recording Equipment receiver?
If you're experiencing no sound from your Shure Recording Equipment receiver, ensure that the transmitter and receiver are linked to the same group and channel. Also, verify levels are registering at the transmitter and that the volume is turned up on the receiver. Check that the receiver is on and that the headphones are properly connected.
Why is there distorted audio in my Shure Recording Equipment?
Distorted audio in your Shure Recording Equipment can stem from several factors. Check the volume levels at the P3T transmitter, ensuring the meter isn't hitting the overload indicator. Inspect levels going in and out of the mixer; distortion anywhere in the signal chain will persist even if the PSM300 system isn't overloading. Ensure the receiver batteries are fresh. Verify that the cables are 1/4 inch balanced to prevent noise introduction. Confirm all cables are fully plugged into the mixer and P3T inputs, as incomplete insertion can cause faint and distorted signals. Finally, use line-level outputs from the mixer, avoiding main speaker outputs from powered mixers, as these amplified signals can overload the P3T inputs.
What causes IR sync failure on Shure Speaker System?
IR sync failure on your Shure Speaker System can occur if the distance between the receiver and transmitter is not between 6-11 cm. Verify the distance.
What to do if Shure Speaker System audio or RF drops out?
If you are experiencing audio or RF dropouts with your Shure Speaker System, consider the following: * Perform a scan to ensure the receiver is on a clear, available frequency. * Ensure a line-of-sight path exists between the transmitter antenna and the bodypack receivers. * Verify that other wireless devices being monitored, like wireless microphones, aren't experiencing RF dropouts. * If using an antenna other than the one included with the system, ensure it's designed for the correct frequency range.
Why does IR sync fail on a Shure Speaker System?
IR sync may fail on your Shure Speaker System if the distance between the receiver and transmitter is not between 6-11 cm. Verify the distance.
General| Tuning Steps | 25 kHz |
|---|---|
| MixMode Control | Yes |
| Type | Personal Monitoring System |
| System Components | Transmitter |
| Frequency Range | 470-952 MHz (region dependent) |
| Transmitter Output Power | 10, 50 mW (region dependent) |
| RF Output Power | 10, 50 mW (region dependent) |
| Audio Input Connector | XLR, 1/4" TRS |
| Audio Output Connector (Receiver) | 3.5 mm TRS |
| Signal-To-Noise Ratio | 90 dB |
| Total Harmonic Distortion | < 0.5% |
| Audio THD | <0.5% |
| Pilot Tone | Yes |
| Power Source (Receiver) | 2 AA batteries |
| Power Supply | Included |
| Operating Temperature Range | -18 to 57°C (0 to 135°F) |
| Number of Channels | 1 |
Details the display, buttons, knobs, and ports of the P3R receiver.
Guides for syncing single/multiple transmitters and receivers.
Guide to setting optimal audio levels for transmitter input and receiver output.
How to select Stereo/MixMode and adjust levels/blends.
Technical details for the PSM300 system, including RF and audio performance.
Technical details for the P3R bodypack receiver.
To Next Page
