For safety reasons, please ensure that
the power cord is disconnected before
opening the case.
L
The product’s colour and specifications may vary from the actually shipping product.
A. Begin Installation
!
Hardware Installation
1. USB 3.2 Ports
(Celeron
Gen 1, Core I
Gen 2)
2. USB 2.0 Ports
3. Power LED
4. Hard Disk Drive LED
5. Power Button
6. SD Card Reader
7. MIC-in
8. Headphones
9. External Power SW & Clear CMOS
10. HDMI Port
11. DisplayPort
12. COM/VGA Port (RS232 only) (Option)
13. COM Port (RS232/RS422/RS485)
(BIOS Setting)
14. LAN Ports
15. Power Jack (DC IN)
16. Connector for WLAN antenna
17. Kensington
®
Lock Hole
1. Unscrew the two screws of the chassis
cover. Slide the cover backwards and
upwards.
1. Unfasten the rack mount screw and remove the rack.
B. HDD or SSD Installation
2. Place an HDD or SSD in the rack and secure
with two screws from each side.
3. Lay the HDD or SSD into its drive bay
and push it gently to the right until it
clicks into place. Refasten screws.
Please press the "Del" key while booting to enter BIOS. Here, please load the optimised BIOS settings.
Operation Position: Please make sure to use either the supplied feet or the VESA mount.
!
Safety Information
E. Complete
1. Please replace and affix the case
cover with two screws. Turn your
DS20U upside down.
2. Connect the power cord.
3. Complete.
e
f
d
1. Locate the SO-DIMM slots on the motherboard.
2. Align the notch of the memory module with the
one of the relevant memory slot.
3. Gently insert the module into the slot in a
45-degree angle.
4. Carefully push down the memory module
until it snaps into the locking mechanism.
5. Repeat the above steps to install an
additional memory module, if required.
D. M.2 Device Installation
C. Memory Module Installation
Latch
Latch
Notch
Cutout
SO-DIMM slot
45-degree
angle
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.
!
a
b
M.2 2242/2260/2280 M key slot
1. Locate the M.2 key slots on the motherboard.
2. Install the M.2 device into the M.2 slot and secure with the screw.
a
b
More information on this product can be found at: https://bit.ly/DS20UV2
Weitere Informationen zu diesem Produkt finden Sie unter: https://bit.ly/DS20UV2
Pour plus d'informations sur ce produit, visitez: https://bit.ly/DS20UV2
Product Overview
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose
of used batteries according to the manufacturer’s instructions.
Das unkorrekte Austauschen der Batterie kann diesen Computer beschädigen. Ersetzen Sie die Batterie nur durch den von Shuttle empfohlenen
Typ oder ein gleichwertiges Modell. Entsorgen Sie gebrauchte Batterien gemäß den Herstellerangaben.
!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device meets the requirements for the EU conformity in accordance to the currently valid EU directives.
2000m
DS20U Series Quick Guide
53R-DS20U3-2002
3 6
1 2 4 5 7 8
2
a
b
Slope angle
b
a
14 15
9
10 11 12 13
17
17
1
1616
b
a
2.5 inch HDD/SSD Slot
c
a
b
b
a
c
DC-IN
Thermal Pad
Pasting a thermal pad on the M.2 SSD
can effectively reduce its temperature.
!
To Next Page
Need help?
General