Siemens 7SA513 - Page 340

$SSHQGL[6$
9

&*&
¿©©©©§©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©§©©©©©§©©©§©©©©©©©©©©©©©©©©¤
   Ann.LSAIEC 60870-5-103 
FNo. Meaning OpFtNo.CAGIBTTypInf
¨©©©©ª©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©ª©©ª©©ª©©©ª©©ª©©ª©©ª©©©ª©©©
2425Back-up earth fault det. highset IE>>  CG18762125
2426Back-up earth fault detection IE>/IEp  CG18862126
2451Back-up overcurrent: General trip  C 18962151
2452Back-up overcurrent: Trip 1pole L1  C 21462152
2453Back-up overcurrent: Trip 1pole L2  C 21562153
2454Back-up overcurrent: Trip 1pole L3  C 21662154
2455Back-up overcurrent: Trip 3pole  C 21762155
2704>AR: Reset auto-reclose function CG  15 GI  40 4
2709>AR: Block delayed auto-reclose CG  76 GI  40 9
2711>AR: External start for internal AR CG  28 GI  40 11
2712>AR: Ext. Trip L1 for internal AR CG  29 GI  40 12
2713>AR: Ext. Trip L2 for internal AR CG  30 GI  40 13
2714>AR: Ext. Trip L3 for internal AR CG  31 GI  40 14
2781AR: Auto-reclose is switched off CG  79 GI  40 81
2782AR: Auto-reclose is switched on CG  CAGI  p 16
2783AR: Auto-reclose is blocked CG  72 GI  40 83
2784AR: Auto-reclose is not ready CG  CAGIBT p130
2785AR: Auto-reclose is dynamically blockedCG 234 GI  40 85
2787AR: Circuit breaker not ready CG  78 GI  40 87
2788AR: CB supervision time expired C  227 4088
2801AR: Auto-reclose in progress CGCG228 GI  40101
2813AR: 1pole dead time for RAR is running CGCG229 GI  40113
2814AR: 3pole dead time for RAR is running CGCG230 GI  40114
2818AR: Evolving fault recognition C  23540118
2833AR: 3pole dead time 1 for DAR running CGCG231 GI  40133
2834AR: 3pole dead time 2 for DAR running CGCG232 GI  40134
2835AR: 3pole dead time 3 for DAR running CGCG233 GI  40135
2851AR: Close command from auto-reclose C  248CA BT p128
2852AR: Close command after 1pole RAR cycleC  25340152
2853AR: Close command after 3pole RAR cycleC  25440153
2854AR: Close command after 3pole DAR cycleC  255CA   p129
2862AR: Auto-reclose cycle successful C  23640162
2863AR: Definitive trip  C 23740163
2871AR: Trip during 1pole AR cycle  C  40171
2931Synchro-check function is switched off CG 119 GI  41 31
2932Synchro-check function is blocked CG 122 GI  41 32
2934Synchro-check function faulty CG 121 GI  41 34
2935Synchro-check supervision time expired C   4135
2941Synchro-check function is running CG 120 GI  41 41
2942Synchro-check function override/bypass C   4142
2943Synchronism (U1>,U2>) detected C   4143
2944Live line,dead busbar(U1>,U2<) detectedC   4144
2945Dead line,live busbar(U1<,U2>) detectedC   4145
2946Dead line,dead busbar(U1<,U2<) detectedC   4146
2947Sync.: Voltage diff. greater than limitC   4147
2948Sync.: Freq. diff. greater than limit C   4148
2949Sync.: Angle diff. greater than limit C   4149
2951Synchronism release (to ext. AR) C  1234151
2961Close command from synchro-check C  1244161
3651Distance protection is switched off CG  55 GI  28 51
3652Distance protection is blocked CG  48 GI  28 52
3653Distance protection is active CG   GI  28 53
3671Dist.: General fault detection  CG1442871
3672Dist.: Fault detection , phase L1  CG145 GIBT 28 72
3673Dist.: Fault detection , phase L2  CG146 GIBT 28 73
3674Dist.: Fault detection , phase L3  CG147 GIBT 28 74
3675Dist.: Fault detection , earth fault  CG148 GIBT 28 75
¥©©©©¦©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©¦©©¦©©¦©©©¦©©¦©©¦©©¦©©©¦©©©¾
www . ElectricalPartManuals . com