11
The cooking time has elapsed
A signal sounds. The oven stops heating. 0:00 is shown in the
display. Press the
0 button. You can set a new cooking time
using the
@ or A button. Or press the 0 button twice and turn
the function selector to the off position. The oven switches off.
Changing the cooking time
Use the
@ or A button to change the cooking time. After a few
seconds, the change is adopted. If the timer has been set,
press the
0 button beforehand.
Cancelling the cooking time
Use the
A button to reset the cooking time to 0:00. After a few
seconds, the change is adopted. The cooking time is
cancelled. If the timer has been set, press the
0 button
beforehand.
Checking the time settings
If several time-setting options are set, the relevant symbols are
illuminated on the display. The time-setting options symbol is in
the foreground and preceded by the
N arrow.
To call up the
V timer, x cooking time, y end time or 0
clock, press the
0 button repeatedly until the N arrow is next
to the relevant symbol. The display shows the value for a few
seconds.
End time
You can change the time at which you wish your dish to be
ready. The oven starts automatically and finishes at the desired
time. You can, for example, put your dish in the cooking
compartment in the morning and set the cooking time so that it
is ready at lunch time.
Ensure that food is not left in the cooking compartment for too
long as it may spoil.
Example in the picture: it is 10:30 am, the cooking time is
45 minutes and the oven is required to finish cooking at
12:30 pm.
1. Adjust the function selector.
2. Set the temperature selector.
3. Press the 0 button twice.
4. Use the @ or A button to set the cooking time.
5. Press the 0 button.
The
N arrow is next to y. The time when the dish will be
ready is displayed.
6. Use the @ or A button to set a later end time.
After a few seconds, the oven adopts the settings and switches
to standby position. The display shows the time at which the
dish will be ready and the
N arrow is next to the y symbol.
The
V and 0 symbols go out. When the oven starts, the
cooking time counts down in the display and the
N arrow is
next to the
x symbol. The y symbol goes out.
The cooking time has elapsed
A signal sounds. The oven stops heating. 0:00 is shown in the
display. Press the
0 button. You can set a new cooking time
using the
@ or A button. Or press the 0 button twice and turn
the function selector to the off position. The oven switches off.
Changing the end time
Use the
@ or A button to change the end time. After a few
seconds, the change is adopted. If the timer has been set, first
press the
0 button twice. Do not change the end time if the
cooking time has already started to elapse. The cooking result
would no longer be correct.
Cancelling the end time
Use the
A button to reset the end time to the current time. After
a few seconds, the change is adopted. The oven starts. If the
timer has been set, first press the
0 button twice.
Checking the time settings
If several time-setting options are set, the relevant symbols are
illuminated on the display. The time-setting options symbol is in
the foreground and preceded by the
N arrow.
To call up the
V timer, x cooking time, y end time or 0
clock, press the
0 button repeatedly until the N arrow is next
to the relevant symbol. The display shows the value for a few
seconds.
Clock
After connecting the appliance to the mains or after a power
cut, the
0 symbol and three zeros flash in the display. Set the
clock.
1. Press the 0 button.
The clock in the display shows 12:00. The time symbols light
up and the
N arrow is next to 0.
2. Use the @ or A button to set the clock.
After a few seconds, the time that has been set is adopted.
Changing the clock
No other time-setting option should have been set.
1. Press the 0 button four times.
The time symbols light up in the display and the
N arrow is
next to
0.
2. Use the @ or A button to change the clock.
After a few seconds, the time that has been set is adopted.
Hiding the clock
You can hide the clock. For more information, please refer to
the section Changing the basic settings.
To Next Page
Loading...
Need help?
General