Siemens iQ700 HS958GE 1B Series - Setting Added Steam; Setting Steam Jet Function; After Steam Operation

en Steaming
18
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
8.
Once the cooking time has elapsed:
‒ If required, you can select other settings and re-
start the operation.
‒ When the food is ready, use to switch the ap-
pliance off.
9.
Dry the cooking compartment.
→"After using steam operation", Page18
Changing the type of steam heating
When you change the type of steam heating, the other
settings are also reset.
1.
Press "Stop"
2.
Press
3.
Press the required type of steam heating.
4.
Reset the operation and use "Start" to start.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
1.
Press the temperature.
2.
Change the temperature using the adjustment line
or enter it directly via the number field ⁠.
3.
Press "Apply".
Changing the cooking time
You can change the cooking time at any time.
1.
Press the cooking time.
2.
Change the cooking time using the adjustment line
or enter it directly via the number field ⁠.
3.
Press "Apply".
11.3 Setting added steam
Requirement:Observe the information about the re-
spective operating mode.
→"Setting options with steam", Page17
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Press "Added Steam" ⁠.
4.
Press the required steam level.
Steam level Added steam
1 Low
2 Medium
3 High
5.
Press "Start" to start the operation.
a The appliance starts heating.
a The setting values and how long the appliance has
already been in operation are shown on the display.
6.
When the food is ready, use to switch the appli-
ance off.
7.
Dry the cooking compartment.
→"After using steam operation", Page18
Changing added steam
You can change or deactivate the added steam func-
tion at any time.
1.
Press the steam level.
2.
Change or deactivate added steam.
3.
Press "Apply".
11.4 Setting the steam jet function
Requirement:Observe the information about the re-
spective operating mode.
→"Setting options with steam", Page17
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Press "Steam jet"
4.
Start the operation.
5.
Press "Steam jet" at the desired time.
Do not use the steam jet until the appliance has
completely heated up.
a The appliance starts to heat the water.
6.
When the water is heated up, press "Steam jet"
again.
Note:If rapid heating is activated, the steam jet
can only be triggered once rapid heating is com-
plete.
a The steam jet is triggered and the appliance adds
clouds of steam to the cooking compartment for ap-
prox. 3 to 5 minutes.
a When the steam jet has finished, the operation con-
tinues to run as normal. Depending on the opera-
tion, the steam jet can be triggered again if neces-
sary.
7.
When the food is ready, use to switch the appli-
ance off.
8.
Dry the cooking compartment.
→"After using steam operation", Page18
Cancelling the steam jet
You can cancel the steam jet at any time.
▶
Press "Steam jet" ⁠.
a The operation continues without the steam jet.
11.5 After using steam operation
Dry the appliance after each steam operation.
Note:Traces of limescale may remain in the cooking
compartment after operation with steam. The functional-
ity of the appliance is not affected by this. You can re-
move traces of limescale using hot water or a cloth
soaked in vinegar. Observe the information on clean-
ing.
→"Cleaning and servicing", Page27
Drying the condensation tray
WARNING‒Risk of burns!
The appliance becomes hot during operation.
▶ Allow the appliance to cool down before cleaning.
Requirement:The cooking compartment has cooled
down.
1.
Open the appliance door.
2.
Note:
The condensation tray is underneath the cooking
compartment.