Siemens SINUMERIK 840D sl - Page 61

08/2005 Overview of Alarms
2-61
© Siemens AG, 2005. All rights reserved
SINUMERIK 840D sl/840D/840Di/810D Diagnostics Guide (DA), 08/2005 Edition
• _N_NC_PRO - System internal: protection zones, NCK global
• _N_NC_GD1 - User: 1. GUD block defined by _N_SGUD_DEF, NCK global
• _N_NC_GD2 - User: 2. GUD block defined by _N_MGUD_DEF, NCK global
• _N_NC_GD3 - User: 3. GUD block defined by _N_UGUD_DEF, NCK global
• _N_NC_GD4 - User: 4. GUD block defined by _N_GUD4_DEF, NCK global
• _N_NC_GD5 - User: 5. GUD block defined by _N_GUD5_DEF, NCK global
• _N_NC_GD6 - User: 6. GUD block defined by _N_GUD6_DEF, NCK global
• _N_NC_GD7 - User: 7. 7th GUD block defined by _N_GUD7_DEF, NCK global
• _N_NC_GD8 - User: 8. GUD block defined by _N_GUD8_DEF, NCK global
• _N_NC_GD9 - User: 9. GUD block defined by _N_GUD9_DEF, NCK global
• _N_NC_MAC - User: Macro definitions
• _N_NC_FUN - User: Cycle programs
• _N_CHc_OPT - System internal: option data, channel-specific
• _N_CHc_SEA - System internal: setting data, channel-specific
• _N_CHc_TEA - System internal: machine data, channel-specific
• _N_CHc_PRO - System internal: protection zones, channel-specific
• _N_CHc_UFR - System internal: frames, channel-specific
• _N_CHc_RPA - System internal: arithmetic parameter, channel-specific
• _N_CHc_GD1 - User: 1. GUD block defined by _N_SGUD_DEF, channel-specific
• _N_CHc_GD2 - User: 2. GUD block defined by _N_MGUD_DEF, channel-specific
• _N_CHc_GD3 - User: 3. GUD block defined by _N_UGUD_DEF, channel-specific
• _N_CHc_GD4 - User: 4. GUD block defined by _N_GUD4_DEF, channel-specific
• _N_CHc_GD5 - User: 5. GUD block defined by _N_GUD5_DEF, channel-specific
• _N_CHc_GD6 - User: 6. GUD block defined by _N_GUD6_DEF, channel-specific
• _N_CHc_GD7 - User: 7. 7th GUD block defined by _N_GUD7_DEF, channel-specific
• _N_CHc_GD8 - User: 8. GUD block defined by _N_GUD8_DEF, channel-specific
• _N_CHc_GD9 - User: 9. GUD block defined by _N_GUD9_DEF, channel-specific
• _N_AXa_OPT - System internal: option data, axial
• _N_AXa_SEA - System internal: setting data, axial
• _N_AXa_TEA - System internal: machine data, axial
• _N_AXa_EEC - System internal: leadscrew error compensation data, axial
• _N_AXa_QEC - System internal: quadrant error compensation data, axial
• _N_TOt_TOC - System internal: toolholder data, TOA-specific
• _N_TOt_TOA - System internal: tool data, TOA-specific
• _N_TOt_TMA - System internal: magazine data, TOA-specific
c = Channel number
a = Machine axis number
t = TOA unit number
There are further internal system data blocks with identifier.
Reactions: - NC not ready.
- Channel not ready.
- NC Start disable in this channel.
- Interface signals are set.
- Alarm display.
- NC Stop on alarm.
Remedy: Correct the machine data or undo the changes made.
Please inform the authorized personnel/service department. There are two determining
machine data for cycle programs: