11.92 9 Examples
9.1.8 Display "Change tool data"
9.1.8 Display "Change tool data"
DISPLAY
NEXT CE
REACTI-
VATE
ENABLE
TOOL
ADD
NEXT CE
DELETE
LAST CE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Change tool data:
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
AUTOMATIC
a
a
a
a
a
a
1.1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
L1:
L2:
R:
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Spec. tool life:
1
1000
1
11
EB
411
20
20
1000
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Spec. tool life:
Magazine:
Location:
Size:
Status:
1234
1
T No.:
Duplo No.:
Prewarning limit tool life:
Geometry:
1
1
Type:
Cutting edge No.:
100
Wear:
L1:
L2:
R:
0.001
0.001
0.002
Softkey "DISPLAY NEXT CE"
Provides the tool data of the next cutting edge.
This key displays the first cutting edge if pressed when the last cutting edge is being
displayed.
Softkey "REACTIVATE"
The selected tool is assigned the "replacement tool" status, the "current tool life" is set to
"tool life presetting".
Softkey "ENABLE TOOL"
If softkey "Add next cutting edge" is operated, the tool is assigned the identifier "Do not
enable tool". After input of the tool data of the second cutting edge, the tool can be enabled
again via softkey "Enable tool".
Softkey "ADD NEXT CE"
A cutting edge is added to the tool available.
A maximum of nine cutting edges is permissible.
Provides display "Change tool data" of next cutting edge.
(By selecting this function, another D No. is entered in the reference list of the tool location
and the NC pointer positioned on it.)
Softkey "DELETE LAST CE"
The last cutting edge of the tool is deleted.
If the tool has only one cutting edge, it cannot be deleted.
© Siemens AG 1991 All Rights Reserved 6FC5 197-0AA40-1BP1 9–9
SINUMERIK 840/880 (PJ)
To Next Page
Loading...
Need help?
General
