Siemens SR23EI28ME Information For Use

en Preventing material damage
10
Preventing material damage
2 Preventing material
damage
Preventing material damage
2.1 Safe installation
ATTENTION!
Improper installation of the appliance
may cause damage.
▶ If the dishwasher is installed above
or below other domestic appli-
ances, follow the information on in-
stallation in combination with a
dishwasher in the installation in-
structions for the individual appli-
ances.
▶ If there is no information or if the
installation instructions do not in-
clude the relevant information, con-
tact the manufacturer of these ap-
pliances to check that the dish-
washer can be installed above or
below these appliances.
▶ If no information is available from
the manufacturer, the dishwasher
should not be installed above or
below such appliances.
▶ To ensure the safe operation of all
domestic appliances, continue fol-
lowing the installation instructions
for the dishwasher.
▶ Do not install the dishwasher un-
der a hob.
▶ Do not install the dishwasher near
heat sources, e.g. radiators, heat
storage tanks, ovens or other ap-
pliances that generate heat.
Contact between the appliance and
water pipes may lead to corrosion of
these pipes, possibly causing them
to leak.
▶ Check that there is a distance of at
least 5cm between the appliance
and the water pipe. The pipes sup-
plied for the drinking water and
waste water connections are not
affected here.
Modified or damaged water hoses
may result in material damage and
damage to the appliance.
▶ Never kink, crush, modify or cut
through water hoses.
▶ Only use the water hoses supplied
with the appliance or genuine
spare hoses.
▶ Never re-use water hoses that
have been used before.
If the water pressure is too high or
too low, the appliance may not be
able to operate properly.
▶ Make sure that the water pressure
in the water supply system is min.
50kPa (0.5bar) and max.
1000kPa (10bar).
▶ If the water pressure exceeds the
maximum value specified, a pres-
sure-reducing valve must be in-
stalled between the drinking water
connection and the hose set of the
appliance.
2.2 Safe use
ATTENTION!
Escaping water vapour can damage
fitted units.
▶ When the programme ends, leave
the appliance to cool down for a
while before opening the door.
Special salt for dishwashers can
damage the tub due to corrosion.
▶ To make sure that any special salt
that escapes is washed out of the
tub, add the special salt to the dis-
penser for special salt immediately
before the programme starts.
Detergent may damage the water
softening system.
▶ Only fill the dispenser of the water
softening system with special dish-
washer salt.
Unsuitable cleaning agents may dam-
age the appliance.
▶ Do not use a steam cleaner.

Siemens SR23EI28ME Specifications

General

Door color	Stainless steel
Cord length	1.75 m
Product size	Slimline (45 cm)
Inlet hose length	1.65 m
Custom panel-ready	Yes
Outlet hose length	2.05 m
Appliance placement	Freestanding
Current	10 A
AC input voltage	220-240 V
AC input frequency	50\\60 Hz
Energy efficiency scale	A to G
Water consumption per cycle	9.5 L
Cycle time	210 min
Noise level	44 dB
Delay start (max)	24 h
Overflow protection	-
Dishwashing programs	60min 65°C, Auto 45-65°C, Eco 50°C, Intensive 70°C, Standard 60°C
Number of place settings	10 place settings
Number of washing programs	6
Number of temperature settings	4
Package weight	43200 g

Weight and Dimensions

Depth	600 mm
Width	450 mm
Height	845 mm
Weight	41996 g
Depth with door open	1155 mm