Signode AM-58 - User Manual

Questions and Answers

S
Shelly SmithAug 5, 2025
Why are strap joints failing after tool removal from Signode AM-58 Packaging equipment?
- B
  Brittany FreemanAug 5, 2025
  If strap joints are failing after removing the Signode Packaging equipment, first verify that the jaws and tool size match the strap size you're using. Then, inspect the sealer mechanism for worn jaws, notchers, and pins, replacing them as needed. Finally, ensure that the strap, seal, and tool are suitable for the application, considering factors like load strength, impact, and potential load expansion.
K
kthomasAug 9, 2025
How to fix feedwheel slippage during tensioning in Signode AM-58?
- E
  Eric DouglasAug 9, 2025
  If the Signode Packaging equipment's feedwheel slips on the top strap during tensioning, it might be due to several reasons. First, try cleaning the feedwheel teeth with a wire brush to remove any dirt or grit. If the teeth are worn or chipped, consider replacing the feedwheel. Also, check the side plate bushing for wear, and replace it if the hole is elongated. Finally, ensure the strap is properly aligned in the tool.
T
Tiffany ChristianAug 14, 2025
What to do if sealing mechanism crushes seals in Signode AM-58?
- W
  watsonerinAug 14, 2025
  If the Signode Packaging equipment's sealing mechanism crushes or deforms seals, first ensure that the jaws and tool size match the strap size being used. Next, make sure to align the strap properly when loading the tool.
K
Kristine MillerAug 18, 2025
Why does the bottom strap slip out during tensioning with Signode AM-58 Packaging equipment?
- M
  marybergAug 18, 2025
  If the bottom strap slips out of the Signode Packaging equipment during tensioning, it could be because the rocking gripper teeth are packed with dirt or grit. Try cleaning them with a wire brush. If the teeth are worn or chipped, you may need to replace the rocking gripper.
M
Michael PattonAug 22, 2025
What to do if Signode AM-58 Packaging equipment won't cut strap after sealing?
- M
  Melissa GrayAug 22, 2025
  If the Signode Packaging equipment will not cut off the strap after sealing, first adjust the cutter. If that doesn't work, the cutter blade may be worn and need replacement. Another possibility is that the cutting leg on the cutter block is worn or broken, requiring replacement of the cutter block.
J
jasonrodriguezAug 27, 2025
Why doesn't the ejector pick up seals in Signode AM-58?
- S
  Sarah TerrellAug 27, 2025
  If the ejector on your Signode Packaging equipment does not pick up seals, it could be due to several reasons: 1. Ensure the seals are properly seated in the cutter block track. 2. Check for and remove any dirt in the cutter block rear track. 3. Replace the ejector if the ejector tip is broken or worn. 4. Tighten any loose screws securing the cutter block to the magazine, applying Loctite #242 to each screw before reassembling. 5. Replace the ejector lever if it is broken or bent.
K
Kaitlyn WatsonAug 31, 2025
What to do if seals don't eject fully from Signode Packaging equipment?
- M
  mjamesAug 31, 2025
  If seals do not fully eject from the Signode Packaging equipment, or if the cutter blade cuts off seal ends, consider the following: 1. Replace the ejector spring. 2. Replace the ejector if its tip is severely worn. 3. Replace the cutter blade if it is severely worn. 4. Check the ejector lever for cracks or bending and replace if necessary. 5. If the screws securing the cutter block to the magazine are loose, disassemble the tool, remove the screws, apply one drop of Loctite #242 to each screw, and reassemble.