Simplicity 1691340 User Manual

How to use this file...(Labels & Miscellaneous Documents)
————————————————————————————————————————————–––
Instructions for
Print Vendors (Paper Manuals)
Paper: * Various...
Press: * Various...
Bindery: * Various...
General: * This instruction page is NOT part of the document and must NOT be printed.
• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY,
and should NOT be printed.
• THIS document will most likely be a unique piece -- either a label or certificate or
other such miscellaneous format.
• EXACT specifications on the print & job specs should already be known to
you. In you are uncertain of what these specifications are, please contact
Simplicity Technical Publications.
• (Note: We will do our best to answer your questions concerning this job, but may need to transfer
you to another department within our company for additional specifications and job
requirements).
————————————————————————————————————————————–––
If you have further questions on how to utilize this file, please contact
Simplicity Technical Publications Department at (262) 284-8647.

Simplicity 1691340 Specifications

General

Cylinders	1
Transmission Type	Hydrostatic
Transmission	Hydrostatic
Drive	2WD
Engine	Briggs & Stratton
Front Tire Size	15x6-6
Turning Radius	18 in
Tire Size (Front)	15x6-6

Summary

Section 1: Commercial Front-Cut Rider with Eaton Model 7 Hydrostatic

Forward & Reverse Travel Stop Adjustment

Limit maximum hydro pump speed.

Section 2: Large-Frame Tractors with Shaft Drive - Sundstrand Model 15 Hydrostatic

Section 2 Neutral Adjustment

Adjust transmission control lever for neutral position.

Section 3: Large-Frame Tractors with Belt Driven - Sundstrand Model 15 Hydrostatic

Section 3 Neutral Adjustment

Adjust hydrostatic control lever for neutral.

Section 4: Tractors with Tuff Torq K215-A & HydroGear BDU-21L

Section 4 Early Model Neutral Adjustment

Adjust speed control lever for neutral position.

Section 4 Late Model Neutral Adjustment

Perform neutral adjustment for late models with kit.

Section 5: Tractors with Eaton 850 Transaxle

Section 5 Neutral Adjustment

Adjust speed control lever and quadrant for neutral.

Section 6: Tractors with Tuff Torq K60 Hydrostatic Transaxle

Section 6 K60 Neutral Adjustment

Align cams for neutral position.

Section 6 (Continued): Tractors with HydroGear 311-0750/311-0800 Transaxle

Section 6 HydroGear 311 Neutral Adjustment

Section 6 HydroGear 311 Return-to-Neutral Adjustment

Section 7: Lawn Tractors with HydroGear BDU10S Transaxle

Section 7 BDU10S Neutral Adjustment (Two Ball Joints)

Section 7 BDU10S Neutral Adjustment (One Ball Joint)

Section 7 (Continued): Lawn Tractors with HydroGear 310-0500 Transaxle (With Hand Control)

Section 7 HydroGear 310 Neutral Adjustment

Section 7 HydroGear 310 Return-to-Neutral Adjustment

Section 7 (Continued): Lawn Tractors with HydroGear 318-0500/322-0650 Transaxle (With Foot Control)

Section 7 HydroGear 0500/0650 Neutral Adjustment

Section 8: Lawn Tractors with Eaton Model 7 Hydrostatic & Peerless 1300 Series Transaxle

Section 8 Neutral Adjustment

Section 9: Later Model Front-Cut Rider with Eaton Model 7 Hydrostatic

Section 9 Neutral Adjustment

Section 10: Early Model Front-Cut Rider with Eaton Model 7 Hydrostatic

Section 10 Neutral Adjustment

Section 11: Mid-Engine Riding Mowers with HydroGear 311-0500

Section 11 Neutral Adjustment

Section 11 Return to Neutral Adjustment