Simplicity 1691886 User Manual

How to use this file...(Labels & Miscellaneous Documents)
————————————————————————————————————————————–––
Instructions for
Print Vendors (Paper Manuals)
Paper: * Various...
Press: * Various...
Bindery: * Various...
General: * This instruction page is NOT part of the document and must NOT be printed.
• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY,
and should NOT be printed.
• THIS document will most likely be a unique piece -- either a label or certificate or
other such miscellaneous format.
• EXACT specifications on the print & job specs should already be known to
you. In you are uncertain of what these specifications are, please contact
Simplicity Technical Publications.
• (Note: We will do our best to answer your questions concerning this job, but may need to transfer
you to another department within our company for additional specifications and job
requirements).
————————————————————————————————————————————–––
If you have further questions on how to utilize this file, please contact
Simplicity Technical Publications Department at (262) 284-8647.

Simplicity 1691886 Specifications

General

Type	Lawn Tractor
Fuel	Gasoline
Transmission	Hydrostatic
Drive	2WD
Engine	Briggs & Stratton
Engine Type	Single Cylinder
Fuel Capacity	2.5 gal
Turning Radius	18 inches
Tire Size (Front)	15x6-6

Summary

Commercial Front-Cut Rider with Dual Eaton Model 7 Hydrostatic

Wheel-Steer Adjustments

Adjustments for steering alignment and neutral positioning of hydro pump linkage for riders.

Neutral Adjustment for Spring-Centered Lever

Ensuring control levers automatically return to neutral position after release.

Large-Frame Tractors with Shaft Drive - Sundstrand Model 15 Hydrostatic

Neutral Adjustment for Shaft Drive Tractors

Procedure to correct tractor creeping when control lever is in neutral.

Large-Frame Tractors with Belt Driven - Sundstrand Model 15 Hydrostatic

Neutral Adjustment for Belt Driven Tractors

Correcting tractor creep for belt-driven hydrostatic systems in neutral.

Tractors with Tuff Torq K215-A & HydroGear (Sundstrand) Hydrostatic, BDU-21L

Neutral Adjustment (Early Model Only)

Specific neutral adjustment steps for early models of this tractor type.

Neutral Adjustment for HydroGear 216-3010L

Procedure to correct tractor creeping for the HydroGear 216-3010L transaxle.

Tractors with Eaton 850 Transaxle

Neutral Adjustment for Eaton 850 Transaxle

Steps to adjust the neutral position for tractors with Eaton 850 transaxles.

Tractors with Tuff Torq K60 Hydrostatic Transaxle

Neutral Adjustment for Tuff Torq K60

Procedure for correcting tractor creep with Tuff Torq K60 transaxles.

Lawn Tractors with HydroGear 311-0750/311-0800 Transaxle

Neutral Adjustment for HydroGear 311-0750/311-0800

Correcting tractor creep for HydroGear 311-0750/311-0800 transaxles.

Lawn Tractors with Eaton 750 or 751 Transaxles

Neutral Adjustment for Eaton 750 (Early Models)

Neutral Adjustment for Eaton 751 Transaxle

Lawn Tractors with HydroGear Sundstrand BDU10S

Neutral Adjustment (Two Ball Joints)

Neutral Adjustment (One Ball Joint)

Lawn Tractors with HydroGear 310-0500 (Hand Control)

Neutral Adjustment for HydroGear 310-0500

Lawn Tractors with HydroGear 318-0500/322-0650 (Foot Control)

Neutral Adjustment for HydroGear 318-0500/322-0650

Lawn Tractors with Eaton Model 7 & Peerless 1300 Transaxles

Neutral Adjustment for Eaton Model 7 / Peerless 1300

Later Model Front-Cut Rider with Eaton Model 7 Hydrostatic

Neutral Adjustment for Later Front-Cut Riders

Early Model Front-Cut Rider with Eaton Model 7 Hydrostatic

Neutral Adjustment for Early Front-Cut Riders

Mid-Engine Riding Mowers with HydroGear 311-0500

Neutral Adjustment for Mid-Engine Mowers