OPERATING THE MACHINE
GTJZ0612E&0812E&1012E&1212E Operation Manual 7-9 © Mar. 2022
3. After selection of charging curve code, press and
hold Select key for 5s, the charging curve code will
flash quickly, release the key, and the battery curve
has been configured.
4. Repeat the steps above if re-change is needed.
To enter EQ mode manually:
1. Press and hold Select key for 10s, when the display
shows EQ in quick flashing, release the key and the
charger has been set in EQ mode.
2. To exit the EQ mode, likewise, press and hold the
Select key for 10s, when the display shows OFF in
quick flashing, release the key and the charger will
exit the EQ mode.
Charger in-built curve codes and respective battery
models
Table 7-2
Curve codes Battery models
B02
Trojan T105
B04 Discover AGM
B05
US Battery Flooded
B07
Trojan T125
B11
Trojan T1275
(two in series and two in tandem)
Note: the default curve code is B04.
INDOOR/OUTDOOR MODE
SETTING-GTJZ1212E
Note: This setting method is for GTJZ1212E machines
only.
NOTICE
The GTJZ1212E-4047E has indoor models and
outdoor models. Indoor models must be used indoor
only, while outdoor models can be used indoor and
outdoor. The max platform height in indoor mode is
11.9m (39ft). When in outdoor mode, the maximum
platform height is limited to 9m (29.5ft).
The indoor mode must not be used in
outdoor applications. Indoor models
can’t be used outdoors.
Note:
• This mode setting is for GTJZ1212E outdoor
models only.
• The indoor or outdoor mode can be set on this
machine. The selected mode will not change when
the machine is turned off. When the machine is
turned on, the previously selected mode is still
selected. You have to check and confirm after each
start up that the machine is in the correct mode, and
change the operating mode corresponding with the
working environment.
SINOBOOM SYSTEM
For programs in Chinese models:
1. Push the "indoor/outdoor mode select switch"
upwards with the machine stowed, and the machine
will be switched to outdoor mode.
2. After the outdoor mode is selected, the decimal
point on the bottom-right on the display screen of
the platform controller will be off, and the maximum
height of the platform is 9m (29.5 ft), that is, when
the platform height reaches 9m (29.5 ft), the
platform will stop rising, with "Od" displaying on the
platform controller.
3. Push the "indoor/outdoor mode select switch"
downwards with the machine stowed, and the
machine should be switched to indoor mode.
4. After the indoor mode is selected, the decimal point
on the bottom-right on the display screen of the
platform controller will be on, and the maximum
height of the platform is 11.9m (39 ft), but when the
platform height reaches 9m (29.5 ft), the platform
will stop rising, with "Id" displaying on the platform
controller. At this time, restore the joystick to the
neutral position and release the joystick, then hold
the "enable switch" of the joystick and push the
handle forward, the platform will continue to rise to
11.9m (39 ft).
For other programs:
1. Push the "indoor/outdoor mode select switch"
upwards with the machine stowed, and the machine
will be switched to outdoor mode.
2. After the outdoor mode is selected, the decimal
point on the bottom-right on the display screen of
the platform controller will be off, and the maximum
height of the platform is 9m (29.5 ft), that is, when
the platform height reaches 9m (29.5 ft), the
platform will stop rising, with "Od" displaying on the
platform controller.
3. Push the "indoor/outdoor mode select switch"
downwards with the machine stowed, and the
machine should be switched to indoor mode.
4. After the indoor mode is selected, the decimal point
on the bottom-right on the display screen of the
To Next Page
Loading...
