Siterwell GS517A User Manual

Product type : Smoke alarm
Item number : GS517A
Supplier name : Siterwell Electronics CO., Limited
Supplier address : No.666 Qingfeng Road,
Jiangbei District, Ningbo, Zhejiang
Province, China, 315034
Website supplier : www.china-siter.com
17
DoP: GS517A-002
EN 14604:2005 + AC:2008
0359
Fire Safety
-4- -5-
• Insert the fixing plug into the gap between the mounng plate and
the smoke alarm to fix your alarm.
• Turn on the AC power. If the mains power connecon is properly
working, the green LED will light up.
• Test the correct acvaon of your smoke alarm by pressing and
holding the test buon unl a beep is generated. If no sound is
generated, the smoke alarm is not funconing properly and should
not be used!
Alarm silence facility
When the smoke alarm has detected smoke and turns into the alarm
mode, you can mute the alarm approximately 8 minutes by pressing the
test buon. Aer that, the smoke alarm automacally resets and returns
into the normal operaon mode. If there are sll parcles of combuson
in the air, the smoke alarm will turn into the alarm mode again.
WARNING: Before using the alarm silence facility, always idenfy the
cause of the alarm and make sure that the circumstances are safe.
Low baery mode
When the baery is running low, the smoke alarm will indicate this with
a repeve beep and flash for approximately 30 days. Replace the
baeries by one of the recommended baery types described in
paragraph “product specificaons”.
• WARNING: Turn off the power before replacing the baeries to avoid
the risk of electrical shocks;
• Remove the fixing plug from the smoke alarm;
• Remove the smoke alarm off of the mounng plate;
• Squeeze in and hold the locking arms on the sides of the AC connector
and pull it away from the mounng plate;
• Open the baery compartment and replace the baery;
• Close the baery cover and plug the AC connector into the smoke
alarm;
• Place the smoke alarm on the mounng plate and secure it by turning
it clockwise.
• Insert the fixing plug into the hole between the mounng plate and
the smoke alarm to fix your alarm.
• Turn on the AC power;
• Test the alarm for correct operaon using the test facility, whenever
the baery is replaced. Press and hold the test buon unl a beep is
generated. If no sound is generated, the smoke alarm is not
funconing properly and should not be used!
Fault warning mode
When the smoke alarm is not funconing properly, it will turn into the
fault warning mode. Try cleaning the smoke alarm (see paragraph
maintenance) or replace the smoke alarm!
Maintenance
• Test this smoke alarm weekly for correct operaon using the test
facility. If the smoke alarm funcons correctly, it will generate a loud
beep. Due to the loudness of the alarm, make sure that you always
stand at arm’s length distance from the unit when you are tesng. If
the smoke alarm does not generate an acousc signal, the smoke
alarm must be replaced immediately!
• Clean the smoke alarm at least once per month to remove dirt, dust
or debris. Use a vacuum cleaner with a so brush and vacuum all
sides and covers of the smoke alarm. Do not remove the top cover of
the smoke alarm to clean it inside.
• Do not aempt to repair this smoke alarm. If the smoke alarm shows
a damage related to its funconality, it must be replaced!
• Trouble shoong: False alarm is oen caused by dust or steam.
Recycling and disposal
The WEEE symbol means that this product and baeries
must be disposed separately from other household waste.
When they reach their end of life, take them to a designated
waste collecon point in your area to guarantee a safe disposal or
recycling. Protect the environment, human health and natural resources!
www.china-siter.com
Idenficaon
SMOKE ALARM
GS517A USER MANUAL
Document nr.: GS517A_Manual_Rev J
Revision nr.: REV J
Revision date: 2018-06-04
Overview LED & acousc signaling
Operang mode LED signal (flash) Acousc signal (beep) Descripon mode
Normal mode 1 x per 32 seconds None Device is funconing properly
AC powered Constantly (green) None Device has AC power connecon
Test mode 1 x per second (red) 1 x per second Device is being tested
Alarm mode 1 x per second (red) 1 x per second Device is detecng smoke
Alarm silence facility 1 x per 8 seconds (red) None Alarm signal is muted
Low baery mode 1 x per 32 seconds (red) 1 x per 32 seconds
(simultaneously) (simultaneously) Baery is running low
Fault warning mode 1 x per 32 seconds (red) 1 x per 32 seconds
(alternang) (alternang) Device is not funconing properly

Siterwell GS517A Specifications

General

Brand	Siterwell
Model	GS517A
Category	Smoke Alarm
Language	English