SKF MAXILUBE MAX 230-IF105 Series User Manual (English)

Questions and Answers:

S
Sheryl EvansAug 21, 2025
What to do if the SKF MAXILUBE MAX 230-IF105 user interface displays alarm for low pressure in a lubrication channel?
- D
  Destiny NicholsonAug 21, 2025
  If the user interface displays an alarm for low pressure in a lubrication channel on your SKF Water Pump, it could be because the lubricant has stiffened in the piping due to operating conditions like cold or heat, there are leaks in the header piping, or there is air in the header piping. To fix this, try setting a longer maximum pressurization time or changing to a more appropriate lubricant. Locate and repair any leakage, and remove air from the header and branch piping. Finally, reset the alarm.
B
Barbara GregoryAug 23, 2025
What does it mean if the SKF MAXILUBE MAX 230-IF105 user interface displays lubricant low level alarm in a lubrication channel?
- A
  Aaron ThomasAug 23, 2025
  If the user interface of your SKF Water Pump displays a lubricant low level alarm in a lubrication channel, this indicates that the lubricant barrel is empty. Replace the lubricant barrel and then reset the alarm.
R
Ricardo OrtizAug 25, 2025
What to do if there is considerable grease leakage at the lubrication point of the SKF MAXILUBE MAX 230-IF105 Water Pump?
- M
  Melissa IbarraAug 25, 2025
  If you observe considerable grease leakage at the lubrication point and the bearing temperature rises in your SKF Water Pump, it suggests that the lubrication cycle has been set too short. Check the correct lubrication cycle at the doser setting table of the lubrication system in question.
K
Kyle StricklandAug 27, 2025
What to do if the SKF MAXILUBE MAX 230-IF105 user interface displays alarm for high pressure in a lubrication channel?
- S
  Stephanie WatsonAug 27, 2025
  If the user interface displays an alarm for high pressure in a lubrication channel for the SKF Water Pump, and the pressure at the pressure control unit is above the set pressure low limit value when pressurization starts, the control valve at the hydraulic part may not be operating. Replace control cartridge CHV-100 when necessary.
W
wstevensAug 28, 2025
What to do if the SKF MAXILUBE MAX 230-IF105 Water Pump does not start?
- J
  Jodi RobertsAug 28, 2025
  If the SKF Water Pump doesn't start, it could be due to several reasons: the pressure air supply might be closed, the pressure air level might not be high enough, or the supply voltage might be off. To resolve this, turn on the pressure air supply by pressing down the shut-off valve button or set the air pressure to 3,5-4,5 bar using the pressure regulator and the pressure gauge. Also, check that the pressure at the pressure air regulator is 3,5-4,5 bar. Inspect the pressure air supply piping for leaks. Ensure the LED-signal of the pump is lit, the supply voltage is on, and the M12 cable is correctly connected and in good condition.
C
Cynthia PerezAug 29, 2025
Why does the SKF Water Pump start but the pressure does not rise?
- J
  James RiveraAug 29, 2025
  If the SKF Water Pump starts but the pressure doesn't rise, the pressure air level might not be high enough. Check that the pressure at the pressure air regulator is 3,5-4,5 bar and inspect the pressure air supply piping for leaks.
S
Shane AllenAug 31, 2025
What to do if the SKF Water Pump starts but the pressure does not rise?
- D
  Dr. Catherine BarryAug 31, 2025
  If the SKF Water Pump starts, but the pressure doesn't rise, the grease filter may be clogged, there may be air in the suction piping of the pump or there may be impurities in the suction head of the pump. You can clean or replace the grease filter cartridge. Remove air from the pump by opening the venting screw of the grease filter or the pressure connection of the pump, ensuring that only grease (not air) comes out.
F
fayalaSep 2, 2025
Why the green LED-signal POWER and the user interface of the SKF Water Pump control center are not lit?
- S
  Sarah RhodesSep 2, 2025
  If the green LED-signal POWER and the user interface of the SKF Water Pump control center are not lit, it could be that the main switch of the control center is in the OFF-position, or the fuse has operated. Turn the main switch to the ON-position and check the fuse.
D
Diana AverySep 3, 2025
How to fix display and LED-signals of the SKF Maxilube Water Pump user interface if they are not lit?
- A
  Austin GarzaSep 3, 2025
  If the display and LED-signals of the SKF Maxilube Water Pump user interface are not lit, it indicates that there is no supply voltage at the pumping center. Check the supply voltage.
A
Alejandro GuerreroSep 5, 2025
What to do if the SKF Control Unit displays a high pressure alarm?
- J
  jason54Sep 5, 2025
  If the user interface of your SKF Control Unit displays a high pressure alarm for a lubrication channel, it could be due to the lubricant stiffening in the piping because of the operating conditions, such as cold or heat, or the control valve of the changeover valve unit is not working. You should set the lubrication cycle longer or replace the lubricant with one appropriate for the operating conditions and reset the alarm. Check that the setpoints for high and low limit pressure are correct. If necessary, contact Oy SKF Ab. Check the pressure of the compressed air. Check the operation of the solenoid valves MV1 and MV2.