EasyManua.ls Logo

Skil TS6307-00 - User Manual

Skil TS6307-00
170 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: To reduce the risk of injury, the user must read and understand the
Owner’s Manual before using this product. Save these instructions for future reference.
AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et
comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide
afin de pouvoir le consulter ultérieurement.
ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender
el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para
consultarlas en caso sea necesario.
Owner’s Manual
Guide d’utilisation
Manual del propietario
Table Saw
Scie à table
Sierra de mesa
For Customer Service
Pour le service à la clientèle
Servicio al cliente
1-877-SKIL-999
OR
www.skil.com
Model/ Modelo/ Modèle: TS6307-00
HEIGH T
+
2
0
15
30
45
22.5
BLADE ROTATION

Table of Contents

Questions and Answers

  • J
    jason71Jul 28, 2025
    Why won't my Skil TS6307-00 start?
    • C
      Connie BellJul 28, 2025
      If your Skil Saw won't start, here's what to check: 1. Make sure the power cord is securely plugged into an electrical outlet. If it isn't, plug it in. 2. See if a fuse has blown or a circuit breaker has tripped. If so, replace the fuse or reset the breaker. 3. Inspect the cord for damage. If damaged, have it replaced by an Authorized SKIL Service Center or Service Station. 4. A burned-out switch could also be the culprit. Have it replaced by an Authorized SKIL Service Center or Service Station.
  • A
    Adam TerryAug 2, 2025
    What to do if Skil Saw cut binds, burns, stalls motor when ripping?
    • M
      murilloandrewAug 2, 2025
      When ripping with your Skil Saw, binding, burning, and motor stalls can occur due to: * A dull blade with an improper tooth set. Sharpen or replace the blade. * A warped board. Ensure the concave or hollow side faces “DOWN” and feed the board slowly. * A rip fence not parallel to the blade. See the “Adjustments” section, “Aligning Rip Fence.” * A riving knife out of alignment. Refer to the “Adjustments” section, “Checking riving knife alignment.”
  • W
    washingtonchristinaAug 7, 2025
    What to do if my Skil Saw circuit breaker trips?
    • J
      joshuagarrettAug 7, 2025
      If the circuit breaker trips repeatedly while you're using your Skil Saw, try replacing the blade with a new one and reduce the force applied to the workpiece during cutting.
  • C
    collieradamAug 11, 2025
    Why is my Skil Saw vibrating so much?
    • D
      Dustin JohnsonAug 11, 2025
      Excessive vibration in your Skil Saw can stem from a few issues: * The bevel lock handle might not be tightened. Refer to the “Getting To Know Your Table Saw” section for instructions. * The blade could be out of balance. If this is the case, discard the blade and use a different one. * The arbor nut may not be tight enough. Consult the “Assembly” section, specifically “Changing the blade,” for guidance.
  • J
    Jacqueline SmithAug 16, 2025
    Why doesn't my Skil TS6307-00 Saw blade come up to speed?
    • A
      Ashley WattsAug 16, 2025
      If your Skil Saw blade doesn't reach full speed, it could be due to: 1. Using an extension cord that is too light or too long. Replace it with an adequate cord. 2. Experiencing low supply voltage. Contact your electric company to resolve this.
  • C
    Cory MaynardAug 22, 2025
    How to prevent plastic from melting when cutting with Skil TS6307-00 Saw?
    • T
      thompsoncesarAug 22, 2025
      Plastic melting or blade tips overheating during cuts with your Skil Saw can be caused by: 1. A feed rate that's too high. Slow down the feed rate through the blade. 2. Blade tips that are not sharp. Sharpen or replace the blade.

Summary

General Power Tool Safety Warnings

Personal Safety

Measures to ensure operator safety during use, including staying alert and using protective equipment.

Table Saw Safety Warnings

Kickback Causes and Warnings

Explains the causes of kickback and provides precautions to avoid it, emphasizing proper workpiece handling.

Adjustments

Blade Angle and Stop Settings

Instructions for setting precise 90° and 45° blade stops and other bevel angle adjustments.

Basic Table Saw Operation

Safety Power Switch and Smart Guard

Covers the safety power switch features and the use of the Smart-Guard System for safe operation.

Cutting Aids and Techniques

Instructions for using blade bevel control, work helpers, rip fence, and miter gauge for various cuts.

Storage and Transportation

Component Storage

Proper storage locations for smart guard components, dust chute elbow, and wrenches when not in use.

Maintenance

Dust Extraction and Cleaning

Information on dust collection ports, elbows, and clearing the dust chute/scoop.

Troubleshooting

Limited Warranty of SKIL Consumer Bench Top Power Tools

Skil TS6307-00 Specifications

General IconGeneral
Motor15 Amp
Bevel Capacity0-45 degrees
Arbor Size5/8 inches
Motor Voltage120V
Blade Diameter10 inches
Cutting Capacity at 90 degrees3.5 inches
Max Cut Depth @ 45 Degrees2.5 inches
Max Rip to Right of Blade25.5 inches
Weight51 pounds

Related product manuals