EasyManua.ls Logo

Skil 5080 - User Manual

Skil 5080
72 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: To reduce the risk of injury, the user must read and understand the
Owner’s Manual before using this product. Save these instructions for future reference.
AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et
comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide
afin de pouvoir le consulter ultérieurement.
ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender
el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para
consultarlas en caso sea necesario.
Owner’s Manual
Guide d’utilisation
Manual del propietario
For Customer Service
Pour le service à la clientèle
Servicio al cliente
Circular Saw
Scie Circulaire
Sierra Circular
1-877-SKIL-999
OR
www.skil.com
Model/ Modelo/ Modèle: 5080/5180/5185

Table of Contents

Other manuals for Skil 5080

Preview: Operating/Safety Instructions
Operating/Safety Instructions44 pages

Questions and Answers

  • R
    Robert HarrisJul 25, 2025
    What to do if my Skil 5080 Saw will not start?
    • C
      Crystal GordonJul 25, 2025
      If your Skil Saw won't start, there are several potential causes: * The power cord might not be plugged in. Make sure to plug the saw in. * A fuse in your power source may have blown, or a circuit breaker tripped. Replace the fuse or reset the breaker. * The cord could be damaged. Inspect it, and if it is, have it replaced by an authorized Skil service center. * The switch may be burned out. In this case, have the switch replaced by an authorized Skil service center. * The safety switch may be engaged preventing the tool from turning on. Disengage the Safety Switch.
  • L
    Luis FisherAug 2, 2025
    Why does my Skil 5080 cut bind, burn, stall, or motor when ripping?
    • C
      Christopher FisherAug 2, 2025
      If your Skil Saw binds, burns, stalls, or the motor strains when ripping, here are some possible reasons: * The blade may be dull or have an improper tooth set. Discard the blade and use a different one. * The board you're cutting could be warped. Ensure the concave or hollow side faces "DOWN" and feed slowly. * The blade might be binding. Assemble the blade and tighten the Vari-Torque clutch. * You may have improper workpiece support. Clamp or support the workpiece correctly.
  • S
    Sean DiazAug 9, 2025
    Why Skil Saw blade does not come up to speed?
    • T
      Timothy ShepherdAug 9, 2025
      If the blade on your Skil Saw isn't reaching full speed, it could be due to: * An extension cord that is too light or too long. Replace it with an adequate cord. * Low house voltage. Contact your electric company.
  • T
    Theresa DanielAug 17, 2025
    How to reduce excessive vibration in my Skil Saw?
    • A
      alyssa34Aug 17, 2025
      Excessive vibration in your Skil Saw can stem from a couple of issues: * The blade may be out of balance. Try discarding the blade and using a different one. * The workpiece might not be clamped or supported properly. Ensure you clamp or support the workpiece adequately.

Summary

General Power Tool Safety Warnings

Electrical Safety

Covers proper grounding, avoiding wet conditions, and cord care to prevent shock.

Personal Safety

Emphasizes user alertness, protective gear, and preventing accidental starts.

Safety Rules for Circular Saws

Keep Hands Clear of Blade

Critical rule to keep hands away from the cutting area and blade.

Avoid Reaching Under Workpiece

Warning that the guard does not protect the blade below the workpiece.

Adjust Cutting Depth

Guides on setting blade depth to match material thickness for safety and cut quality.

Secure Workpiece

Instructs to always secure the workpiece to a stable platform.

Use Insulated Gripping Surfaces

Advise to hold tool by insulated surfaces when risk of electrical contact exists.

Use Correct Blades and Hardware

Ensures safety and performance by using specified blades, washers, and bolts.

Hold Saw Firmly

Kickback Causes and Warnings

Firm Grip and Arm Position

Maintain a firm grip and position arms to resist kickback forces.

Blade Binding or Interrupting Cut

Release trigger and hold saw motionless; never pull backward while blade moves.

Lower Guard Function

Details on checking and ensuring the lower guard operates freely and correctly.

Additional Safety Warnings

AC Tools with AC Power Supply

Warning against using AC tools with DC power supply due to hazard risk.

Power Cord Service

Specifies that power cords must be serviced by authorized Skil centers only.

Symbols (Continued)

Wear Eye Protection Symbol

Mandates the use of safety goggles or glasses with side shields and a face shield.

Functional Description and Specifications

Circular Saw Diagram

Model and Specifications

Assembly

Attaching the Blade

Step-by-step guide for safely installing the saw blade, including safety warnings.

Vari-Torque Clutch

Operating Instructions

Depth Adjustment

Bevel Adjustment

Safety Switch Operation

Details on using the safety switch to prevent unintentional starting.

Tool Switch Operation

General Cutting Techniques

Cutting Masonry;Metal Warning

Warning against using abrasive wheels with this saw due to potential guard failure.

Plunge Cuts

Rip Cuts

Maintenance

Service and Repair

Cleaning Procedures

Blade Care and Sharpening

Extension Cords

Recommended Extension Cord Sizes

Troubleshooting

Saw Will Not Start

Binding, Burning, or Stalling

Troubleshooting guide for common problems encountered during ripping operations.

Skil 5080 Specifications

General IconGeneral
TypeCircular Saw
Blade Diameter7-1/4 inches
Arbor Size5/8 inches
Cord Length6 feet
No Load Speed5, 300 RPM
Motor Power15 Amp

Related product manuals