EasyManua.ls Logo

Skil 5380 - User Manual

Skil 5380
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
IMPORTANT: IMPORTANT : IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
For English Version Version française Versión en español
See page 2 Voir page 15 Ver la página 28
Operating/Safety Instructions
Consignes de fonctionnement/sécurité
Instrucciones de funcionamiento y seguridad
1-877-SKIL999 (1-877-754-5999) www.skil.com
Call Toll Free for
Consumer Information
& Service Locations
Pour obtenir des informations
et les adresses de nos centres
de service après-vente,
appelez ce numéro gratuit
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
5380
5385
5480
5485
SM 1619X05344 03-10:SM 1619X05344 03-10 3/10/10 3:06 PM Page 1

Table of Contents

Questions and Answers

  • C
    Christopher RodriguezJul 31, 2025
    What to do if my Skil 5380 will not start?
    • T
      Teresa WhiteAug 1, 2025
      If your Skil Saw won't start, possible causes include: the power cord isn't plugged in (plug the saw in); a tripped fuse or circuit breaker (replace the fuse or reset the breaker); a damaged cord (inspect and replace if necessary at an authorized service center); a burned-out switch (have it replaced at an authorized service center); or the safety switch is engaged (disengage the safety switch).
  • R
    Ryan LopezAug 6, 2025
    Why does my Skil 5380 Saw cut bind, burn, and stall when ripping?
    • J
      Jesse YoungAug 6, 2025
      If your Skil Saw cut binds, burns, and stalls motor when ripping, the causes and solutions are: * A dull blade with improper tooth set. Discard the blade and use a different one. * A warped board. Make sure the concave or hollow side is facing 'DOWN' and feed slowly. * Blade binds. Assemble the blade and tighten the Vari-Torque clutch. * Improper workpiece support. Clamp or support the workpiece.
  • M
    Melissa HerreraAug 12, 2025
    Why is my Skil 5380 blade not coming up to speed?
    • D
      Danielle RichardsAug 12, 2025
      If the blade of your Skil Saw is not reaching the correct speed, this could be due to an extension cord that is too light or too long (replace it with an adequate cord) or low house voltage (contact your electric company).
  • M
    Ms. Caroline SmithAug 19, 2025
    What to do if Skil Saw has excessive vibration?
    • Y
      ymckinneyAug 19, 2025
      Excessive vibration in your Skil Saw can be caused by: * A blade that is out of balance. Discard the blade and use a different one. * A workpiece that is not clamped or supported properly. Clamp or support the workpiece.
  • L
    Laura KimAug 25, 2025
    Why Skil 5380 Saw blade is slipping?
    • T
      Terry GomezAug 25, 2025
      If the Skil Saw blade is slipping, it means that tool does not cut workpiece. To fix this, assemble the blade and tighten the Vari-Torque clutch.

Summary

General Power Tool Safety Warnings

Work Area Safety

Electrical Safety

Personal Safety

Circular Saw Safety Rules

Safe Cutting Procedures

Details safe practices for blade contact, guarding, workpiece support, and depth adjustment.

Kickback Warnings and Prevention

Understanding Kickback

Explains kickback as sudden saw reaction and provides operator prevention methods.

Lower Guard Operation

Details the importance and operation of the lower guard for preventing injuries.

Further Safety Precautions

Electrical Safety Aids

Tool Description and Specs

Tool Assembly

Blade Attachment Guide

Step-by-step instructions for safely attaching the saw blade, including guard operation.

Vari-Torque Clutch Explanation

Explains the function of the clutch in reducing kickback by allowing the blade to slip.

Operating the Saw

Adjusting Blade Depth

Guides on adjusting the blade depth for optimal cutting and minimal splintering.

Safety Switch Usage

Details on how the safety switch prevents accidental starts and its function.

Angle and Bevel Adjustments

Procedure for verifying and adjusting the saw's 90° cutting angle and bevel settings.

Cutting Techniques

Line Guide and Switch Use

General Cuts and Safety

Specialized Cutting Methods

Plunge Cut Instructions

Cutting Large Panels

Maintenance and Servicing

Rip Cutting Methods

Troubleshooting Guide

Startup and Speed Issues

Diagnoses issues like saw not starting or blade not reaching speed, with remedies.

Cutting Performance Problems

Addresses vibration, binding, burning, stalling, square cut, and blade slipping problems.

Skil 5380 Specifications

General IconGeneral
TypeCircular Saw
No-Load Speed5, 300 RPM
Blade Diameter7-1/4 inches
Max Cutting Depth at 45 Degrees1-13/16 inches
Arbor Size5/8 inch
Dust Port Size1-1/4 in
Motor Power15 Amp

Related product manuals