To Next Page
M
melissa13Aug 13, 2025
Why can't I change the miter angle on my skilsaw SPT62MTC Saw?
- IIan HarrisAug 13, 2025
If you cannot change the miter angle, it's likely because the miter lock lever is tightened. Loosen the miter lock lever.
Why can't I change the miter angle on my skilsaw SPT62MTC Saw?
If you cannot change the miter angle, it's likely because the miter lock lever is tightened. Loosen the miter lock lever.
Why won't my Skilsaw Saw motor start?
There are several reasons why the motor might not start: * The tool might not be plugged in. Ensure the tool is plugged into a working power outlet. * A fuse may have blown or a circuit breaker tripped. Replace the fuse or reset the breaker. * The brushes may be worn. In this case, contact a SKILSAW Authorized Service to have them replaced. * The cord could be damaged. Have it replaced by a SKILSAW Authorized Service.
Why does my skilsaw SPT62MTC vibrate or shake?
Your Skilsaw Saw may vibrate or shake due to: * A saw blade that is not round, or a damaged or bent saw blade. Replace the blade. * A loose saw blade. Tighten the blade bolt. * Other issues. Contact SKILSAW Authorized Service.
What to do if my skilsaw SPT62MTC Saw blade binds, jams or makes rough cuts?
If the blade binds, jams, or causes rough cuts, check the following: * Ensure the material being cut does not exceed the cutting capacity. * The blade may be dull, damaged or bent. Replace the blade. * The blade may be improper. Use only blades recommended for this tool and the material being cut.
Why is my Skilsaw Saw tool slow to start?
The tool's slow start is due to the soft start feature. No action is required, as this is normal.
What to do if the head assembly won't fully rise or the blade guard won't fully close on my Skilsaw Saw?
If the head assembly doesn't fully rise or the blade guard doesn't fully close: * It could be due to part failure or pivot/guard spring issues. Contact SKILSAW Authorized Service. * The cover plate may not be properly placed after changing the blade. Tighten the cover plate properly. * Chips/debris accumulation. Remove accumulated chips.
Why is the angle of cut not accurate on my skilsaw SPT62MTC?
If the angle of cut is not accurate, the fence may be misaligned. Adjust the miter scale pointer.
What to do if the blade hits the tool base on my skilsaw SPT62MTC Saw?
If the blade hits the tool base, it is likely due to blade misalignment. Contact SKILSAW Authorized Service.
Key safety advice and instructions to read before operating the tool.
Toll-free number and website for consumer information and service locations.
Essential safety guidelines for operating benchtop power tools to prevent accidents.
Guidelines for maintaining a safe and organized work environment.
Precautions for personal safety while operating power tools.
Guidelines for safe electrical connections and usage of the power tool.
Proper methods for using and maintaining the power tool for safety and longevity.
Requirements for qualified personnel performing tool maintenance and repair.
Specific safety rules for operating saws to prevent injuries.
Safe practices for handling workpieces during cutting operations.
General advice for safe tool operation, emphasizing awareness and control.
Explanation of double insulation design and its safety implications.
Guidelines for selecting and using appropriate extension cords with the tool.
Specifications for connecting the saw to a suitable electrical power supply.
Information on the tool's limits for cutting different materials and dimensions.
Labels and descriptions for various parts of the saw.
Instructions for unpacking the saw and verifying all parts are present.
Step-by-step guide for safely removing and installing saw blades.
Detailed steps for safely detaching the saw blade.
Instructions for securely fitting a 12-inch saw blade.
How to calibrate the miter scale pointer for precise angle settings.
Safe methods for moving the saw to prevent injury or damage.
Steps to take before lifting or mounting the saw to ensure safety.
Instructions for securely bolting the saw to a workbench.
Alternative method for securing the saw using clamps.
How to safely turn the saw on and off using the power switch and lock.
Correct posture and hand placement for safe and effective sawing.
How to use the integrated clamp to secure workpieces.
Techniques for supporting longer workpieces to prevent tipping.
Methods for providing extra support for various workpiece types.
Procedure for performing a straight cross cut at a 0° miter angle.
Procedure for making angled cuts using the miter scale.
Instructions for safely removing and emptying the chip collection tray.
Guidelines for servicing, brush examination, and replacement.
Safe procedures for cleaning the tool and maintaining blade condition.
Recommendations for lubricating moving parts and bearing maintenance.
Troubleshooting steps for issues related to the tool's electrical system.
Troubleshooting common operational issues like blade binding or inaccurate cuts.
General| Type | Circular Saw |
|---|---|
| Motor | 15 Amp |
| Weight | 8.8 lbs |
| Power Source | Corded Electric |
| Voltage | 120V |
| Arbor Size | 5/8 inch |
| Max Cutting Depth at 90 degrees | 2-3/8 in |
| No Load Speed | 5, 300 RPM |
| Cord Length | 8 ft |
| Blade Diameter | 7-1/4 inches |
