skilsaw SPT99T - User Manual

Questions and Answers

J
jessicawardJul 28, 2025
What to do if my skilsaw Saw will not start?
- J
  James MartinJul 28, 2025
  If your skilsaw Saw won't start, here are a few things to check: * Ensure the power cord is properly plugged in. If not, plug the saw in. * Check the fuse or circuit breaker. If it's tripped, replace the fuse or reset the breaker. * Inspect the cord for damage. If damaged, have it replaced by an Authorized SKILSAW Service Center or Service Station. * A burned-out switch could also be the culprit. In this case, have the switch replaced by an Authorized SKILSAW Service Center or Service Station.
L
Leslie MoonAug 1, 2025
Why does my skilsaw Saw cut bind, burn, and stall the motor when ripping?
- C
  christopher49Aug 1, 2025
  If your skilsaw Saw experiences binding, burning, or motor stalling during ripping, the following could be the causes: * A dull blade with an improper tooth set. Sharpen or replace the blade. * A warped board. Ensure the concave or hollow side faces “DOWN” and feed slowly.
M
Michael MorenoAug 6, 2025
Why does my skilsaw SPT99T have excessive vibration?
- B
  Brian SandersAug 6, 2025
  Excessive vibration in your skilsaw Saw can be attributed to several factors: * Failure to tighten the bevel lock handle. * An out-of-balance blade. Discard the blade and use a different one. * The saw is not securely mounted to the stand or workbench. Tighten all mounting hardware.
J
Jessica DuncanAug 12, 2025
Why does the blade of my skilsaw SPT99T not come up to speed?
- S
  steven48Aug 12, 2025
  If the blade on your skilsaw Saw isn't reaching full speed, it could be due to: * An extension cord that is too light or too long. Replace it with an adequate cord. * Low supply voltage.
M
Melissa RossAug 16, 2025
What to do if plastic melts or blade tips overheat when cutting with my skilsaw Saw?
- C
  Christopher HollandAug 16, 2025
  If you notice plastic melting or blade tips overheating while cutting with your skilsaw Saw, consider the following: * Your feed rate might be too high. Slow down the feed rate through the blade. * The blade tips may not be sharp. Sharpen or replace the blade.
B
Brittany MunozAug 22, 2025
Why is the tilt lock handle elevation wheel hard to move on my skilsaw Saw?
- A
  Alexander FryAug 22, 2025
  If the tilt lock handle or elevation wheel on your skilsaw Saw is difficult to move: * The bevel lock handle may not be loosened when making a tilt adjustment. * Saw dust may be present on the depth screw threads.

Summary

General Safety Rules

Work Area, Electrical, and Personal Safety

Essential safety practices for operating power tools, covering work area, electrical, and personal protection.

Table Saw Specific Safety

Blade Guarding and Cutting Safety

Critical warnings for guards, riving knives, and cutting procedures.

Kickback Prevention and Operation Safety

Understanding kickback causes and safety rules for operation.

Adjustments and Calibration

Blade Angle and Parallelism Adjustments

Rip Fence and Riving Knife Alignment

Procedures for aligning the rip fence and riving knife for optimal cutting.

Riving Knife and Table Insert Adjustment

Basic Table Saw Operation

Controls, Guards, and Work Helpers

Using the power switch, smart guard, work helpers, and fence controls for safe operation.

Cutting Techniques: Ripping and Crosscutting

Advanced Cutting Operations

Troubleshooting Guide

Common Saw Problems and Solutions

Identifying and resolving issues such as starting problems, vibration, and cut quality.

skilsaw SPT99T Specifications

General

Motor	15 Amp
Blade Diameter	7-1/4 inches
Weight	11.5 lbs
Amperage	15 Amps
Arbor Size	5/8 in
Cord Length	6 ft
No Load Speed	5000 RPM
Electric Brake	Yes
Dust Port	Yes
Warranty	1 year limited